Anshan mechanism wholesale cast iron pipe cast iron drainage pipe

Emerging Products Co., sales of cast iron pipe cast iron drainage pipe in recent years, widely used in construction in the drainage system of pipes. The pipe belongs to the metal type centrifugal casting, compact structure, high tensile strength; its uniform thickness and smooth surface; with flexible interface, rubber seals, has a good seismic performance, and it can block noise transmission, the quietest pipeline; the pipes can withstand high temperatures, fire performance, to meet fire safety requirements; it is corrosion-resistant, anti-aging, long service life. Flexible cast iron cast iron drainage pipe is ideal for high-rise buildings and high-rise building drainage pipe. First, the technical characteristics of flexible cast iron drainage pipe installation is simple, flexible, relatively cement twisted mouth method of installation greatly reduces installation labor costs and improve installation speed. At the same time easy disassembly, it is conducive to maintenance, Chaigai and replacement pipes. Easy-to-pipeline trap when correcting the alignment of sanitary ware outlet. Second, the main method of flexible cast iron drainage pipe construction of flexible cast iron cast iron drainage pipe into an interface flange clamp flexible interfaces and flexible primary installation method. Its use is currently on countries with specific regulatory requirements, we combine the product description summarizes its installation and construction methods from the installation process: (a), clamp-type flexible interface installation method, installation should be based on the required length, the straight pipe fixation with abrasive cutter off, vertical section shall, smooth, without flash, burrs, so as not to hurt the rubber seals. 2, with a special wrench or screwdriver clamp connections loosen the clamp bolt, remove the rubber ring, the clamp set into the lower duct. 3, the rubber trap into the lower end of the pipe, the upper tube into the rubber ring, the two interfaces flat for good. Finally, the clamp set into the rubber ring. 4, with a special wrench or screwdriver clamp connection clamp locking bolt, so tight strap securely in place to prevent the tightening force is too large, screw slippage. Second, flexible seismic cast iron drainage specifications and main technical indicators cast iron drainage pipe to length: 1 m, 1.5 m, 1.83 m, 3 m. Pipe main specifications are DN50, DN75, DN100, DN125, DN150, DN200, DN250, DN300. The tensile strength of the pipe ≥150Mpa, hydrostatic testing P≥0.3Mpa, straight tube bend ≤2mm / m. Good seismic performance of the tube, the amount of axial vibration within 2mm pressure 0.1Mpa no leakage, the amount of radial displacement ± 30mm, pressure 0.1Mpa no leakage. Flexible seismic cast iron pipes at the same time with a variety of oblique three, sailing tees, oblique cross, sailing Stone, 90 degree elbow, 45 degree elbow, blind blocking, S-type trap, P-type deposit water bend, and other common stereotypes tapered pipe fittings, ancillary use. Product properties using centrifugal casting process. Tensile strength ≥ 150Mpa, pipe ring compressive strength ≥ 350MPa, hardness 160-210HB, pipe factory hydrostatic test, the test pressure ≥ 0.45MPa. Anticorrosive epoxy paint coating the pipe outside use of iron red rust. Cast iron pipe connection mechanism should be flexible cast iron pipes, special washer (EPDM) and accessories. Pipe wall thickness does not allow negative deviation, positive deviation should be less than GB / T corresponding provisions allowing deviation of mean outside diameter or meet the European standard provisions allowing positive bias. Cast iron and cast iron pipe fittings shall adopt the same standards. Cast iron pipe connections made of stainless steel clamp connection. Response: Our products comply with the above requirements. 4.2 Technical parameters meet the design requirements. 5. Technology Services 5.1 has improved service network (in Beijing professional service locations). When a problem occurs, they should arrive at the scene in four hours, for processing. 5.2 Contractor shall require equipment suppliers to send at least one experienced technical staff to demand-side installation site supervision of installation work. Additional Notes technology and equipment conditions existing main production units are as follows: (1) 105㎡ ring sintering machine, one Taiwan, 616m3 blast furnace, with an annual 800,000 tons of hot metal; (2) DN80-1000MM cooled metal centrifuge 5 , DN1000-1600MM heat molding centrifuge 2, with an annual production capacity of 400,000 tons; (3) welded flange pipe production line, the annual production capacity of 10,000 tons; (4) DN100-1000MM special spraying pipe production line 2 annual production capacity of 50,000 tons; (5) DN50-300MM drain electrostatic spraying production line one, the annual production capacity of 20,000 tons; (6) cast pipe production line, the annual production capacity of 20,000 tons; (7) Main public auxiliary facilities: 1500 Nm3 / h oxygen machine, 30 000 m3 / h gas tank 1. Transaction Description building cast iron drainage pipe - cast iron pipe specifications - cast iron pipe prices - cash on delivery