GS8 series three labyrinth cyclone separator Features

GS8 series three labyrinth cyclone separator GS8 series three labyrinth cyclone separator is a combination of AS7 series and QF series separator upgrade again, more efficient steam and compressed air systems to remove entrained liquid droplets occasions. Model GS8 series three labyrinth cyclone separator size DN15-350 Interface Interface Type Flange -PN16 / PN25 / PN40 / PN64 Body material carbon steel WCB / stainless -SS304 & SS316 maximum working pressure 16BAR / 25BAR / 40BAR / 64AR The maximum operating temperature of 425 ℃ Figure thirteen labyrinth cyclone separator features: maximum separation efficiency (dryness 99.9%), the lowest drop (about five thousandths); structural design according to Pressure Vessel Code. Installation GS8 separator must be installed in a horizontal line, straight down the drain, all calibres were GS8 separator with mounting bracket can reduce pipeline to carry. To ensure that the separated liquid discharged rapidly, connect the appropriate combination of a trap (float traps) in the drain GS8 separator bottom. When GS8 three labyrinth cyclone separator application in the presence of air in the steam system, air may accumulate in the upper part of the separator. At this point, it should be in air vent, install plug at the air port. GS8- Separators size table (Dimension) SIZE Specification Design pressure Design pressure (MPa) External dimensions (mm) Dimensions Volume capacity (L) ABCDEFGHJK DN15 1.6 350 200 450 108 120 1/2 1/2 121 148 30 2 DN20 1.6 350 200 450 108 120 1/2 1/2 121 148 30 2 DN25 1.6 350 220 500 159 120 1/2 1/2 95 213 30 6 DN32 1.6 350 220 500 159 120 1/2 1/2 95 213 30 6 DN40 1.6 360 220 500 159 120 1/2 3/4 100 213 30 6 DN50 1.0 420 252 638 219 159 1 3/4 100 263 30 18 DN65 1.6 420 252 638 219 159 1 3/4 100 263 30 18 2.5 420 252 638 219 159 1 3/4 100 263 30 18 DN80 1.6 523 332 735 273 145 2 3/4 125 368 30 33 2.5 523 332 735 273 145 2 3/4 125 368 30 33 DN100 1.6 574 337 795 324 163 2 3 / 4 125 384 40 51 2.5 574 337 795 324 163 2 3/4 150 384 40 51 DN125 1.6 656 310 843 356 230 2 3/4 150 416 44 67 3.0 656 310 843 356 230 2 3/4 150 416 44 67 DN150 1.6 706 347 935 406 246 2 3/4 150 466 60 96 3.0 706 347 935 406 246 2 3/4 150 466 60 96 DN200 0.6 850 460 1200 500 372 2 2 175 560 60 185 1.6 850 460 1200 500 372 2 2 175 560 60 185 3.0 850 459 1200 500 372 2 2 175 568 60 230 DN250 0.6 950 615 1580 600 530 2 2 175 688 72 333 1.6 950 615 1580 600 530 2 2 175 688 72 333 3.0 960 615 1580 600 530 2 2 175 698 72 333 DN300 0.6 1000 740 1700 600 540 2 2 200 688 72 330 1.6 1000 740 1700 610 540 2 2 200 688 72 330 3.0 1010 740 1700 610 540 2 2 200 698 72 330 DN350 0.6 / 1.6 / 3.0 1100 754 1800 700 525 2 2 200 816 72 537 DN150 1.6 970 490 1260 620 372 2 2 175 764 72 290 DN250 1.6 1175 615 1500 824 440 2 2 175 980 108 535 Note: To properly install safety information means, and have qualified operators in accordance with Operating guidelines for commissioning and maintenance, to enable it to operate safely. To correct use of tools and safety measures. When installing piping and equipment, to comply with installation and safety guidelines. Isolation does not close when you install an isolation valve repair parts will cause damage to the system, cause harm to humans, the risk of further comprising: Close up of protective devices and and airway or alarm system. Ensure the isolation valve is closed, to avoid shock to the system. Pressure Maintenance repair the pipeline to consider whether there is media in the product before maintenance ensure that the pressure medium is isolated and secure the airway is open to the atmosphere, which is by installing drain valve will be easy to solve. Even if the pressure gauge to zero and do not believe the system to evacuate. There must be a period of time so that the temperature close the isolation valve operating portion temperature close to room temperature, to avoid scalding. Protection coat is a must. Disposal of this product can be recycled. Handled properly does not cause ecological problems. Installation Information NOTE: Before installing the operating read "Precautions." Check materials, the maximum pressure and temperature. If the product is lower than the maximum operating conditions of the system it is installed, make sure that the system has a safety device to prevent overpressure. Check the installation position and direction are correct. Remove the protective cover from all interfaces. Splitter-demand thermal protection. Installation GS8 mounted on a horizontal pipe vertically down the drain. All caliber separator are equipped with mounting brackets to reduce the pipeline to carry, there are two drilled holes on each bracket. In order to ensure a liquid separator drain away as quickly as possible, the discharge port must be connected to a suitable drain valves, or steam traps. Recommended float traps. Float traps have water that is exclusive features. For the case where the air contains air, the air gathered in the upper part of the separator. In this case the appropriate drain valve installed in the exhaust air port. If you do not install the drain valve, you must remove the plastic protective cover, fitted class3000lb carbon steel cock. Debugging After installation or maintenance ensure that the system to be able to completely run. Test on alarm or protection. Installation example (Figure 1) is used to run a small droplet separator and the accumulation of gas / vapor stream containing separation. Relatively heavy droplets after impact falls within the baffle separator drain connection out of the system by the steam traps, such as for air or gas distribution system, using the drain valve excluded. Maintenance: Please read the "Notice" carefully before performing any maintenance operations. No internal parts need repair!