Northern Heavy Machinery production of multi motor test platform

Function Beizhong complete motor test platform: can be used as motor repair test platform, vibration test platform, tensile testing platform, fatigue test platform, engine test platform. According to the platform and its load-bearing requirements to select the appropriate specifications when the user selects the cast iron motor test platform (motor workbench). The following is our cast iron motor test stand (motor workbench) Profile: First, the cast iron motor test platform (motor workbench) purposes: mainly used for mechanical, electrical, engine power experiments, has good stability and plane toughness. Surface with T-slots and bolt holes, can be used to fixed laboratory equipment. Second, the cast iron motor test platform (motor workbench) Material: high-quality high-strength gray cast iron HT250-300, face hardness HB200-240, after two artificial annealing 600 ℃ -700 ℃, the complete removal of internal stress. The accuracy of product stability, good wear resistance. Third, the cast iron motor test stand (motor workbench) Specifications: 1000 × 1000-3000 × 6000 (larger than this size can be spliced ??manufacturing test platform; special sizes can be customized drawings). Fourth, cast iron motor test platform (motor workbench) Precision: According to the national standard verification procedures, according to customer requirements processed into two, three, fine plane. Fifth, cast iron motor test platform (motor workbench) Finish: Face machining T-slot, also available with bolt holes. Artificial scraping the surface plane ensure accuracy. Non-processed surface to remove sand and rust colored. Six, cast iron motor test stand (motor workbench) style: stiffener plate. Seven, cast iron motor test stand (motor workbench) Package: wooden packaging. Anti-rust treatment before packaging and proper packaging to avoid damage due to poor packing products during transport. The plate was certified by, should be accompanied by product certification; should manufacture date and serial number on the product certification. Eight cast iron motor test stand (motor workbench) Technical requirements: 1, cast iron plate Face not have a serious impact on the appearance of the sand holes and performance of pores, cracks, slag, shrinkage, scratches, bumps, rust spots and other defects. 2, the casting surface of the plate should be clear sand and smooth, painted solid. 3, precision registered as 0 - Class 3 flat work surface, the hole diameter of less than 15mm of sand allows the same material clogging hardness less than the hardness of the surrounding material. Face clogged sand hole should be limited to four, and the spacing between the holes of sand should not be less than 80mm. 4, cast iron plate should be made of high quality fine gray cast iron or alloy material, its face hardness should 170-220HB. 5, flat working surface shall normally be by scraping process. Processing adopting scraping Face plate 3, the maximum allowable value of the surface roughness Ra 5um. 6, flat working surface flatness tolerances specified in Table 2. 7, cast iron plate Face uses scrapers process should be painted on the research test. After the contact point of the research area ratio shown in Table 3 are predetermined: 25mm × 25mm square or press the contact area of ??a predetermined number of points are shown in Table 3, and should any of 25mm × 25mm between the contact point of not more than 5:00. Nine, cast iron motor test stand (motor workbench) Instructions for use: 1, before using non-corrosive gas, anti-rust oil wash the face, and wipe clean with skimmed cotton, can be used. 2, the temperature change will make the measurement errors, should be used in a range of 20 ± 5 ℃. 3, when used with a spirit level to adjust the level so that uniform distribution of the pivot fulcrum. 4, when used carefully to prevent collisions. 5, after use wipe, coated anhydrous acidic anti-rust oil, moisture-proof paper cover, in a clean dry place. 6, weekly inspection period: the longest weekly inspection of one year. North Heavy main products: cast iron plate, cast iron platform, crossed platforms, testing platforms, welding platform, motor test platform, machine table, measuring platform, fitter platform, cast iron table, the assembly platform, boring and milling machine table, floor boring machine table, T-slot platform, machine tool castings, machine mattress box, marble platform, cast iron plate bending, iron round platform, to track. Welcome to inquire, there is always one is you need, the North Heavy Industries will be happy to help you! 0317-8250620 8258735 or http://www.btbzjx.com