Yueyang oblique oblique horn iron factory Derek wedges of good quality

Wedges: the material can be cast HT200-300, number Q235,45 steel, copper alloys. Wedges action: install the machine of concrete can be very flat, it can be of wood and be smooth and firm. When you install, unscrew the adjustment screw, the machine is placed on wedges load disk, and then screwed into the screw from above. Adjust the machine guide rails, moving clockwise when the machine rises, counterclockwise when the machine fell, after a good tune compression nut. Install the machine in the area, and if the height difference between the ground plane exceeds the adjustment range of the product, you can increase the gasket between the machine and load the disc. Machine vibration horn rubber creep phenomenon, tend to be stable after 14 days, so the use of machine tools, 14 days after the first level adjustment wedges Use: wedges generally used in pairs, on a concrete foundation first place a good level horn, then two oblique horn horn cross placed on the flat, with a hammer when adjusting two wedges, wedges borrow a slope so the device to increase or decrease to adjust the level of purpose. leveling good After then wedges and spot welding equipment base, make horns stable and secure. Finally, concrete poured, so the device is in a good state level during operation, reducing machine wear and reduce the cost of replacement equipment parts. wedges main Uses: for horizontal and parallel alignment of various equipment, the equipment vibration does not occur during operation, tilt, to ensure good operation of the machine to reduce machine wear, ensure the safety of equipment; features are: easy to use, convenient, fast, mostly manufactured according to the user's needs, according to the actual requirements of the equipment chassis design wedges drawings, and then by drawing manufacture oblique horn Material: synthetic rubber, resistant to oils and coolants made oblique horn purposes: effective attenuation of the machine itself vibration, to reduce vibration forces rumored to prevent vibration force passed to regulate the level of machine height range is also large. Oblique horn use characteristics: 1. machine can be installed in place immediately produce 2 shorten the installation cycle, saving installation costs 3 can rough, finishing equipment consisting reasonable production unit, shorten turnaround route workpiece, reduce product turnaround process step The collision damage and reduce the production cost of 4 may at any time according to the process, production needs, adjust the machine position to reduce the secondary installation costs wedges distributor and quantitative controller. Note: wedges distributor and quantitative controller Shot the core of the core components of the device, when the pellets from the hopper into the first to enter the dispenser, high-speed rotary distributor, the pellets are brought people quantitative controller, the controller with the quantitative orifice into the high-speed transmission impeller. Under the effect of centrifugal force, pellets quickly thrown blade movement along the curve. In the repair, use, in the course of the installation process must be noted: (1) axial radial clearance and the end of the dispenser and quantitative ask gap between the controller must be strictly controlled. Gap is too small, into the impact of pellets, prone to the distributor and quantitative controller asked the little pellets of radial ejection amount is not enough; ask gap is too big, pellets accumulate more prone to spray is not timely, and quantitative controller is stationary, it will happen to twist in the case of high-speed rotation of the distributor and pellets, accelerated wear and damage. (2) periodic inspection flow control external traffic controllers and regulatory function is intact, otherwise the situation will also appear stacked pellets. Life assessment Shot blasting machine is the main basis for quality control. Factors that affect the quality of life of a lot of shot blasting, in addition to the impact of these critical components, as well as: machine vibration, high temperature bearing parts, pulleys slide, there are issues such as pellets on the drive shaft, which requires repair use, the installation process, you must pay attention to: (1) blast wheel contact surface of the bottom plane and asked the guide rail installation is more than 95%, allowing concave to reduce vibration. (2) Select good quality bearings to reduce bearing its own clearance; ensure adequate cooling and lubrication. (3) to ensure the pulley bore and shaft with interference fit; keyway and key with a transition fit. (4) According to blast wheel use conditions, the sealing of the blasting have high demands. When the gap between each impeller wear shield within the shield is larger than the diameter of the pellets can happen, should control the gap between each wear protective plate in less than lmm, namely to avoid leakage into the pellet core section.