Terminal Pull Tester 500N tensile testing machine manufacturer for OEM OEM warranty ..

OEM OEM factory direct supply cost-effective Description: SDL terminal tensile tester is the company for a harness test equipment and electronics industry developed, designed to detect a variety of harness terminals of the pull-out force. Configurable NK, SH force gauge and special fixtures, the instrument has a small device, control accuracy, high accuracy, easy specimen clamping, simple operation, and other characteristics, it is ideal for harness manufacturers to ensure product quality. Feature: horizontal installation. Manual operation is easy and stable. This machine can be installed on the table (table) use to make the rack more stable. Length × width × height: 450 × 260 × 160mm. Effective stroke: 50mm. Rated Load: 500N. (You can also configure 1000N) Weight: 10.5Kg. Instrument pushing Rally: General Standard configuration of several significant push Rally SH-500. (You can also configure pointer pushed Rally of NK-500, different prices) Digital Force Gauge Model: SH-500. Maximum load: 500N (Kg, N and ib three units can be automatically converted). Resolution: 0.01N. Accuracy: ± 0.5%. Output Interface: RS 232 ?? abalone outlet. Power: The power: 220V / AC; Battery continuous operation time: 6 to 8 hours. Stability: Drift: 0.2uV / ℃ (0 ~ 60 ℃); Zero drift: ≤ 0.1% / 8 小时 / FS. Calibration range: full scale calibration. Ambient temperature: 0 ~ + 60 ℃. Humidity: ≤ 80%. Allow overload: 150%. Power supply: the 5th Nickel cyanide battery pack / 220V AC charging 4 to 6 hours. Analog Force Gauge Model: NK-500. Maximum load: 500N (50Kg). Push rod stroke: 10mm. Working temperature: 20 ℃ ± 10 ℃. Transport temperature: -27 ℃ ~ + 70 ℃. Relative humidity: 15% ~ 80% RH. Working environment: no source around and corrosive media. Customers may need to configure the corresponding load specifications count: pointer pushed Rally specifications NK-10,20,30,50,100,200,300,500. Digital Force Gauge HF-2,5,10,20,50,100,200,500,1000 specifications and other equipment left fixtures: * Dimensions: 115mm × 180mm × 30mm. · Scope: Mainly used in plug strength testing, tensile testing harness terminals, etc.. ? Standard load: 500N, maximum load: 1000N. Right fixture of the instrument: · Model: SJ-06. · Scope: all kinds of cables, glass, leather, all kinds of electrical components and other materials tension, destructive, pluggable wiring harness terminals and other tensile testing. ? Standard load: 500N, maximum load: 1000N instrument installation method: 1, base installation method: The instrument can be mounted on the table, make the instrument more stable. Please make sure to install the work surface level, to give the exact value of the test. Please refer to the installation (length × width: 430mm × 80mm, 4 x M4 threaded holes) installed. 2, pushing or pulling force installation method: A, with M4 wrench dynamometer mounting plate 4 M hexagon socket head screws 4 × 16 is released, remove the dynamometer mounting plate; B, install SH series ( Digital Force Gauge) push pull timing, with M4 hex wrench in the pocket of the Annex 4 socket head cap screws M4 × 10 through holes 90 × 40 dynamometer mounting plate screwed into the dynamometer 4 a M4 threaded hole, the dynamometer dynamometer attached to the mounting plate; or Phillips screwdriver attachment pocket 4 Cross recessed pan head screws M3 × 10 passes through the inner dynamometer, the dynamometer Total installed dynamometer mounting plate. 4 1) Install NK series (pointer pushed Rally) push pull timing, with a Phillips screwdriver to push the Rally of the back cover; the mounting plate holes 145 × 30 is screwed into the dynamometer four M3 threaded holes M Remove the screws × 10, the attachment pocket four M3 × 14 Phillips head screws through the mounting holes 145 × 30 dynamometer mounting plate, screw after dynamometer cover four M3 threaded holes (M3 × 10 screws to remove the threaded holes); 2) After installing the force gauge sheet with inner M4 hex wrench dynamometer mounting plate back onto the rack above. Left fixture installation method: M4 hex wrench in the accessory pocket four socket head cap screws M4 × 10 of the fixture through the left mounting plate four adjustment holes screwing four M4 machine screw hole in the base plate the left gripper is mounted to the machine base plate. Right fixture installation method: first screw nut M6 with attachments to the dynamometer load rod, then right gripper is screwed to the dynamometer load rod adjusting nut M6 can make the right firm fixture in succession . General test procedure: 1, all kinds of wiring harness terminals into the left end of the wire portion fixture clamp mouth, rotate the handle to steady the wire clamp portion (harness terminals has been pressed). 2, the other end of the terminal wiring harness into the right gripper folder mouth, rotate the handle to keep the harness terminals at one end stuck in the middle. 3, with inner M4 hex wrench, left center and right center alignment jig fixture. 4. If using SH series (digital push-pull meter) push pull time, turn the power on until after the LCD display to zero. 5, if the installation NK series (pointer pushed Rally) push pull timing, click the toggle button, the finger back to zero bit. 6, rotation of the handle body motivation to left clamp moves to the left and right gripper can be jammed terminals. Daily Care and Maintenance: 1. Do not overload to use, the instrument rated load of 500N. 2, pay attention to routine maintenance work, keep the instrument clean the parts. 3, please contact the manufacturer when the machine fails or point of sale (do not disassemble, repair).