500w fiber laser cutting machine video

 500w video fiber laser cutting machine, laser cutting machine video operation Contact: Mei Jingli: 027- 84656255 QQ: 1961445267 welcome your call. Fiber laser cutting machine laser cutting machine narrow kerf: The laser beam is focused to a small spot, the focal point to achieve high power density, the material is heated to vaporization degree quickly evaporated to form holes. Fiber laser cutting machine cutting machine cutting surface is smooth: no burr cutting surface, cut surface roughness of the general control within Ra6.5. Fiber laser cutting machine cutting machine speed: cutting speeds up to 10m / min Maximum positioning speed of up to 30m / min is much faster than the line cutting speed. Good quality laser cutting machine: the collapse of non-contact cutting edge, trimming heat-affected small, basically no workpiece thermal deformation, completely avoid material formed when punching, slitting generally does not require secondary processing. Metal laser cutting machine Laser oxygen cutting: Laser oxygen cutting principle is similar to oxyacetylene cutting. It is used as a preheating laser source with active gas such as oxygen cutting gas. Blowing out gas on the one hand and cutting metal, the occurrence of the oxidation reaction and emit a lot of heat of oxidation; on the other hand the molten oxide and melt blown out of the reaction zone, a cut in the metal. Metal laser cutting machine laser scribing and breaking control: laser scribing is the use of high energy density laser light to scan the surface of the brittle material, and the material is heated to evaporate a small groove, then apply some pressure, brittle material will along small groove at the split. Laser scribing lasers typically used Q-switched lasers and CO2 lasers. Metal laser cutting machine laser vaporization: the use of high energy density laser beam heats the workpiece, the temperature rose rapidly, within a very short time to reach the boiling point of the material, the material begins to vaporize, forming a vapor. These vapor discharge rate is large, the vapor ejected while the material in the notch. Laser cutting machine laser melting of metal cutting: cutting laser melting, the metal material is heated by laser to melt, and then the non-oxidizing gas through the injection beam coaxially with a nozzle, so that rely on a strong pressure of the gas discharged liquid metal to form a notch. Laser cutting is not necessary to melt completely vaporized metal, the energy required for vaporization of only 1/10. Laser cutting is mainly used to melt some of the cut material or activity is not easily oxidized metal, such as stainless steel, titanium, aluminum and its alloys. Laser cutting machine is sheet metal processing technology development direction, widely used in machine tools, construction machinery, electrical switch manufacturing, elevator manufacturing, food machinery, textile machinery, locomotive manufacturing, agriculture and forestry machinery, food machinery, special vehicles, oil machinery manufacturing, aviation aerospace, environmental protection equipment, household appliances manufacturing, silicon steel and other large electrical machinery manufacturing and processing industries. Laser cutting machine technology advantages: positioning accuracy 0.03mm, repeat positioning accuracy 0.01 mm; laser beam is focused to a small spot, the focal point to achieve high power density, the material is heated to vaporization degree quickly evaporated to form holes. With the beam and the material is relatively linear movement, so that the holes are continuously formed through a narrow slit. Kerf width is generally 0.10 ~ 0.20mm. Laser cutting machine can cut non-metal processing: such as plastic, wood, PVC, leather, textiles, glass and the like. Laser cutting machine laser processing without mold, no mold consumption, not repair mold, saving time change the mold, thus saving processing costs, reduce production costs, especially for machining large products. Laser cutting machine surface without burr, cut surface roughness is generally controlled within Ra6.5. Laser can be steel, stainless steel, aluminum plates, carbide processing, no matter what kind of hardness, can be cut without distortion. Laser cutting machine laser processing flexible, can process any graphics, you can cut the pipe and other profiles. Cutting speeds up to 10m / min, maximum positioning speed up to 150m / min, much faster than linear cutting speed. When the non-contact cutting edge collapse, trimming heat-affected small, basically no workpiece thermal deformation, punching completely avoid material formed slit generally does not require secondary processing. Laser cutting head is not in contact with the surface of the material to ensure no scratched workpiece. Specific advantages of laser cutting machine performance is as follows: 1. slotted narrow, high precision, slotting roughness is good, no re-treatment after cutting the following process. 2. The laser processing system itself is a computer system, you can easily arrange, modify, for personalized processing, especially for some complex contour shape sheet metal parts, lots more small quantities, product life cycle is not long, From a technical and economic point of view to measure the costs and time, manufacturing mold worthwhile, laser cutting machine particularly attractive. 3. The energy density of the laser machining large, short duration, small heat-affected zone, heat distortion small, thermal stress, coupled with a non-mechanical contact laser machining the workpiece without mechanical stress, suitable for precision machining. The high energy density of the laser light is sufficient to melt any metals, particularly suitable for a number of material processing high hardness, high brittleness, high melting point means the other process difficult to process. 5. The processing costs. One-time investment in equipment is more expensive, but continuous, a large number of machining ultimately reduce processing costs per part down. 6. The non-contact laser processing, inertia, processing speed, software programming with the NC system CAD / CAM, the time-saving convenience, high overall efficiency. 7. The laser cutting machine high degree of automation, can fully enclosed processing, pollution, noise, greatly improve the operator's working environment. Wuhan High Energy Laser Equipment Manufacturing Co., Ltd. is a professional laser equipment development, production and sales of high-tech enterprises. The company was founded in 1999, precise positioning and strong technical strength to the rapid rise in Wuhan high energy laser fields, as the world's leading manufacturer of laser processing equipment. Benign configuration of professionals and management personnel, so that enterprises operating in the double-British simultaneously, on business complement each other, not only successfully developed a laser device with international advanced technology, but also the use of import and export right, the product promotion to Hong Kong, South Korea, Vietnam, Malaysia, Thailand, Australia, the United States, Japan, Germany, the Netherlands, Jordan, more than 40 countries, in the same industry in the international market occupy an absolute advantage. Fiber laser cutting machine: http: //www.gnlaser.com/