Guangzhou Degong TDP-1.5T small aluminum single punch tablet press machine laboratory medicine fight press ..

TDP single punch tablet press TDP single punch tablet press Main purpose: This machine is used for all kinds of granular materials into the wafer, is suitable for laboratory prototype and small-scale production. It features a small desktop electric continuous tablet machine that can also hand. The machine can be installed only one pair dies, filling depth, tablet thickness of the material can be adjusted. TDP single punch tablet press Features: This model performance, adaptability, easy to use, easy maintenance, small size, light weight, can also be hand-piece without electricity. The machine just installed a pair dies, filling depth, tablet thickness of the material can be adjusted to accommodate a variety of pressing pharmaceutical industry, medicine tablet pressing requirements and other industry requires a variety of similar products, by the majority of the industry users. TDP single punch tablet press Technical parameters: Model TDP-1.5 maximum compression pressure (kN) 15 Maximum tablet diameter (mm) 12 Maximum filling depth (mm) 12 Maximum tablet thickness (mm) 6 Production capacity (tablets / hour ) 6000 motor power (kW) 0.37 Dimensions (mm) 700 * 370 * 800 Weight (kg) 45 TDP small, single punch tablet press used to press medicine tablets, medicine tablets, calcium tablets, buccal tablets, spirulina tablets, milk tablets, candy tablets, effervescent tablets, chewable tablets, seasonings block, moth balls (mothballs), aromatic tablets, disinfectant tablets, catalyst, fertilizer tablets, pesticides film, button batteries, electronic components, powder metallurgy ceramics tablets. Applicable to the pharmaceutical, health products, food, agriculture, chemicals, electronics batteries, metallurgy and other industries producing ceramics and experiment. The machine good performance, adaptability, easy to use, easy maintenance, small size, light weight, can also be hand-piece without electricity. The machine is equipped with a pair dies, filling depth, tablet thickness of the material can be adjusted to accommodate a variety of pressing pharmaceutical industry, requires medicine levy agents and other industry pressing requirements of various similar products, the majority of users by the industry welcome. Price concessions quality assurance welcome new and old customers advice! 1. This machine is a small desktop tablet press, motor drive, stamping various tablet! 2, the machine can be all kinds of small particles, coarse powder presses round or shaped tablet, suitable for laboratory or small batch production of various tablets, sugar tablets, calcium tablets, shaped like. 3, the machine does not apply to punch large solid, moist or fine powder. 4, the machine structure is simple, easy operation, high degree of automation for punching various shapes of tablets packed in a solid wooden bench (can also be installed in the cement platform) with three M12 paid to the foot screws. Position at the work surface to the surface of the body of about 60 centimeters for the convenience of a demolition repair, wooden bench in the corresponding undershoot core rod hole should have a diameter of about 35 mm. Second, before turning the motor power before the motor take a good ground, the ensure safety. Then remove the V-belt, turn on the motor power, motor start to observe the motor rotation direction is correct (rotation direction of the motor shaft should be shielded or by direction of the arrow on the wheel and vice versa) if the rotation does not, then separate the wiring, then put V-belts installed. Handling and adjustment of a tableting die, die installation: 1, the installation of the red spin punch Panasonic fixing screws, turn the hand wheel to undershoot core rod to its highest position, the punch rod into the lower hole under the red core rod (note the lower punch notch slant aligned under the red fastening screws, and to be inserted in the end) The last punch tighten the screws. 2, installed on the red core punch loosen the fastening nut, put on the red core rod into the hole in the red core rod, to be inserted in the end, get stuck on the red fastening nut with a wrench on the red core rod tightening the lower part of the Six-Party . 3. Loosen the installation mold mold fixing screws, put the mold into the mold to get level anti holes in plywood, while the lower punch into the hole in the mold, press die in the end and then tighten the screws. When put in the mold should be noted that the flat in the mold, so as not to get stuck into a crooked, damaged cell walls. 4. Turn the pulley, the upper punch die slowly lowered into the hole, to observe whether the collision or friction phenomenon. In the event of a collision or friction, loosen the mold platen fixing screws (two), adjust the position of the fixed mold platen, the upper punch enters the die hole, then tighten the mold platen fixing screws, so adjust It means no impact or friction side qualified for the installation of the punch into the die until. Second, adjusting the pieces turn the hand wheel so that the next punch to its highest position, observation blurted surface is flush with the plane of the mold (or high or low will affect the film) if Sarkozy loosen the butterfly screw line, Loosen the rotation adjustment gear on the gear plate, the lower surface of the mold blurted plane together, and then continue on the platen press, butterfly row tighten the screws. At this point, with a hand pulley, empty running ten turn, if the machine is working properly, it can feed pressure test, the next step adjustment. Third, adjust the depth of the filling (ie tablet weight adjustment) Loosen the butterfly screw line, release the gear plate. Adjusting gears make a left turn at the next red core rod is increased, the filling depth reduction (weight loss pills). After adjustment will close on the gear plate, tighten the screws butterfly row. Fourth, adjust the pressure (ie tablet hardness adjustment) Loosen the connecting rod jam nut and turning on the red core rod, make a left turn on a red core rod moves downward, the pressure increased, increasing the pressure out of the tablet hardness: On the contrary, turn right, the pressure is reduced, lower tablet hardness, with a wrench on the lower part of the six-party red core rod after a good tune, will link the lock nut. So far, the adjustment of the die basically completed, and then start the motor pressure test ten She tablets, check the tablet weight, hardness and surface finish quality, etc. as qualified, you can feed production. In the production process, still always check the tablet quality, timely adjustment. Five die Removal 1. Loosen the demolition punch on the red fastening nut, you can pull out the upper punch, if with a tight, hand clamp live on the red lever to pull it out, but be careful not to damage punch shuttle edges. 2. Loosen the demolition die mold fixing screws. Chong unscrew the mounting screw, loosen the butterfly screw line, release the gear plate. Turn the adjustment gear enables undershoot core rod rises about 10 mm, and gently turn the hand wheel so that the next red core rod will top out a part of the mold, the mold will be removed by hand, if the mold fit tightly in the hole, not forced to turn the hand wheel hardtop, so as not to damage the parts. Then shall remove the mold platen and then remove the mold. 3, under demolition rushing fixing screws have been unscrewed first, the sub-hand wheel so make undershoot core rod rose to the highest position, you can manually pull out the plunger. If closely, hand clamp out (be careful not to damage the punch hook blade). 4, after the demolition die yet to turn the adjusting hand wheel, so the red core rod to withdraw about 10 mm, turn the hand wheel to undershoot core rod rose to the highest position, which is not higher than the top end of the mold platen surface with can (This step is not to be ignored in order to avoid re-use under the red core rod and the die contradict the accident). Finally, still under the red fixing screws screwed on. Sixth, lubrication and maintenance of the machine 1, all moving parts lubricated friction surface is to ensure the normal operation of the machine and prolong the life of an important part, especially if the major moving parts in the case of dry Transfers rapid deterioration in oil can not be used Therefore tableting machine before being used all the oil cup hole and lubricate the friction surface, and empty running so that all the friction face full of film, and then be put into use. Press to refuel next class, but each refueling can not be too much to avoid spillovers clean, contamination pills. Each refueling site and the number of refueling in the table below: 2, to be inspected before each shift each screw is loose, in the course of their work should always pay attention to check, if loose, tightened immediately to avoid failure. Its main parts are: the red fastening nut on the mold fixing screws, set screws undershoot: rod lock nut locking set screw rod: lifting fork lock nut (2) butterfly row screw: die in Taiwan board fixing screws (2). Refueling site and the number of refueling refueling site table number each time the lubricating oil refueling spindle hole cup (2) butter 2 2-3 times eccentric shell oil cup (1) 2-3 3 bridge axle grease Oil Cup (1) butter 4 2-3 times the lift cam groove (ie large gear inside of the recess) butter each inspection grooved surface wipe dirt butter filling a five cam groove butter each inspection, depending on the 6 GEARS situation refueling butter each inspection, as the case may fuel oil hole 7 1 8 link lever swing fulcrum of oil on the surface of the oil 1 red core rod 9 of the second lift lever 10 surface oil 2 times 3, before and after each use, transfer courses are required to test each hand pressing a few pieces, no problem and then open electric tablet. 4, in the tabletting process must always check the quality of the die, if there is lack of edge, crack, become a serious loss, should be replaced to avoid damage to the machine malfunction and affect the tablet quality. 5. After each use the remaining particles removed, rub the machine ministries. If the down time is longer, shall remove the dies, the machine each friction surface, Face wipe, coated with anti-rust oil, dust-proof clothing cast; immersed in oil saved die should wipe.