Free shipping CPC non-reactive polymer adhesive bitumen-based waterproofing membrane

Free shipping CPC non-reactive polymer adhesive bitumen-based waterproofing membrane a product description and image descriptions for 1, Product Description free shipping CPC non-reactive polymer adhesive bitumen-based waterproofing membrane moisture content of the grass-roots, no special requirements as long as no clear water to construction. If the phenomenon of time out of water, polymer cement waterproof adhesive material may be too diluted, the adhesive layer so that appeared too thin, uneven, sticky leakage phenomenon, will affect the bond strength of membrane construction quality; if but grass the moisture content is too low, it will cause the polymer cement waterproof adhesive material is not sufficiently hydrated, the adhesive strength of the adhesive layer results in reduced or chalking. Engineering Practice has proved that when the moisture content of grass at 30% to 50%, the effect of construction CPC non-bituminous waterproofing membrane self-adhesive base polymer of the best. 2, image descriptions for Second, product characteristics 1, CPC-reactive non-bituminous waterproofing membrane seams lap width: roofing projects, the long side, the short side lap width should not be less than 80mm; underground works, the long side the short side lap width should not be less than 100mm. 2, CPC-reactive non-bituminous waterproofing membrane adjacent to the short side seams should be staggered 1m above the level of the corner (the angle between the wall and the wall) from the seam angle is more than 0.3m, an additional layer of joints must be waterproof layer joints staggered over 0.3m. 3, CPC reactive non-bituminous waterproofing membrane underground waterproofing seams should be staggered at the corner of the web, the position joints should be more than 0.3m from the corner, at a vertical angle (the angle between the floor and the wall) membrane joints should In the horizontal plane, the position of the corner joints should be away more than 0.6m. 4, the protective layer construction must be waterproof layer after acceptance. Clean the cleaning surface and waterproof layer, to protect construction material of membrane channel transport, construction workers should wear soft-soled shoes to operate. Third, transportation and storage 1, in the transport and storage of the web, should prevent the sun, water, mechanical damage, high fever. 2, a single-layer sheet should stand up (storage period of less than 30 days may be two stand up) for a period of less than 20 days shipping stack up to level five. 3, the web may not be in contact with a variety of organic solvents and other harmful substances. Fourth, the construction method 1, CPC non-bituminous waterproofing membrane self-adhesive base polymer of 2% by weight of cement, namely a bag of cement (50kg) equipped with a bag of adhesive (1.0kg). Preparation of the adhesive and 6kg ~ 10kg bag of cement dry mixed evenly, then added with stirring to 27.5kg ~ 32.5kg of water (phase 2, CPC non-bituminous base polymer self-adhesive waterproofing membrane when the cement weight 55% to 65%, or 2.5 outside the box volume), gradually stir after adding the rest of the cement, while adding cement while stirring, stirring until no clots, no precipitation, no air bubbles can be used. 3, CPC non-bituminous waterproofing membrane self-adhesive base polymer to prevent accidental damage and ultraviolet radiation, the protective layer to be added to extend the membrane life. Protective material cement-based materials should be based, permanent buildings and spend one roof 1: 2.5 cement mortar using 30mm thick or 20mm thick doing fine aggregate concrete rigid protective layer, non-permanent and non-accessible roof construction can be polymer cement brushing two do about 1.0mm thick flexible protective layer. Fifth, the implementation of the standard free shipping CPC non-reactive polymer adhesive bitumen-based waterproofing membrane in line with GB 507957 "Roof Engineering Quality Acceptance", GB50345 "Roof Waterproofing technical specifications" provides underground waterproof leveling layer should be consistent with GB 50208 "Underground Waterproof Engineering Quality Acceptance ", GB50108" underground waterproof technical specifications "requirement. Sixth, the project view picture