Compressor manufacturers build | Qin Wei Air (certified) | XUNYI compressor manufacturer

For the reciprocating piston compressor mechanism, inertia force that can not be eliminated, so running vibration, high noise, the need for specialized fixed base when the larger piston compressor installation. A rotary screw compressor movement mechanism, well-balanced well-known manufacturer of air compressors, vibration, low noise, no installed base. Reciprocating piston compressor is intermittent supply, gas pulsation when running large, high speed screw compressors, stationary gas, no gas pulsation, can meet the requirements of high volume users. Piston compressor basically no automatic control system. Screw compressors are perfect automatic control and protection system, are electromechanical integration products, to facilitate the maintenance and management of air compressor equipment manufacturers, but also to maximize the reduction of energy consumption. Rotary screw compressors can tolerate high speed, so the structure is much smaller volume than the same displacement piston compressor, the same power of the compressor displacement is also much larger. Plus cooler inside the exhaust gas temperature is lower than the piston compressor is about 50 to 60 degrees. If you use too many aircraft types, too scattered, it is neither easy device management, but also increased the number of wearing parts, is bound to increase the cost of normal operation. While the dispersed arrangement is exacerbated by the pollution of the production environment. Piston compressor piston ring wear existence, running despite the oil scraper ring on the piston, but still there is a lot of oil went to the cylinder, the one with the gas discharge. Thus while reducing gas quality, it also increased the fuel consumption. Screw compressor systems with high-efficiency gas separation and filtration equipment, supply high-quality, fuel consumption is low. Based on the above compressor manufacturers build relevant circumstances, many domestic enterprises in the use of the low-pressure compressor, the phasing out of high operating costs, low reliability of the piston compressor compressor manufacturers, wholesale, with Instead efficient screw compressors, in developed countries has become a reality. Based on the above said, in order to reduce production costs and increase economic efficiency, easy device management. 8, clean moisture separator moisture separator structure similar to the oil and gas tanks, air intake against the wall design, so the formation of a centrifugal force, the weight factor due to water and gas, compressed air can be effectively separated in the water. Moisture separator cleaning: open the moisture separator cover, you can use detergent immersion cleaning. 9, correcting all the parameters of all the above components and dry after cleaning the air compressor to start the installation, all components attached to the compressor should again check for omissions and clean during installation tools and other items used. Wash load reduction valve (inlet valve) bis (1) Cleaning: as intake valves dirt more serious, then replace it with a new cleaning cleaning agent, the cleaning process to wash the dirt should be washed after much cleaner parts parts. Cleaned parts rinsed again with fresh water to prevent corrosion and shorten the service life of components, the components washed with water should be placed in a clean dry place to avoid iron rusting parts. Should purge valve and place the body in contact with the valve in note smoothness of the surface, and should be cleaned, replace it if necessary, otherwise it will cause will have when the compressor can not start with a load (a large plant with a load start start phenomenon). (2) Installation components: Component installation removed anti-press steps. Should make is when you install components, component location and activity of installed seals should be coated with an appropriate amount of oil can install seals better, more flexible moving parts. Note: Due to the unloader valve more parts, if not sure to remember the location of each part can be cleaned after each split a component mounted on the component, but members do not install to the body, until all the parts are cleaned then assembled together to the valve body. (3) unloader valve aside to complete the cleaning process to be loaded into the compressor. Compressor manufacturers build | Qin Wei Air (certified) | XUNYI compressor manufacturer is provided by Compressor Co., Ltd. Xianyang Qin Wei. Xianyang Qin Wei Compressor Co. (www.xykyj.cn/) is Xianyang, compression, separation equipment leader, over the years, the company implement the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customer needs. Qin Wei Pneumatic leadership with the staff warmly welcome all inquiries negotiations to create Qin Wei Pneumatic better future.