Stainless acid ink

The ink of the acid stainless steel products are mainly used various metals, glass, vacuum plating, water plating, electrophoresis, anodized aluminum, electrolytic plate, aluminum plate, spray, spray, electrostatic painting surface, face painting and a variety of Oxidation ceiling panels, mirror panels, film board, roll coating plate and other products, silk screen printing. 2 Features: light, good adhesion, fast-drying, anti-stamping. 3, thinner: Division I B-03 special thinner open oil or 783, with 718 net wash water cleaning screen. 4, curing agents: one component, can also choose to add our special hardener JS-10 is used to increase adhesion of the ink and physical and chemical resistance. 5, ink formulation method: cans Stir well, taking the required amount of printing ink diluted to a suitable viscosity. To add a curing agent, reinforcing stand for 10 minutes after the first agent stirring until the ink is completely crosslinked with a curing agent after dilution. 6. Drying time: drying at room temperature, dry time 5-10 minutes, drying time in less than 24 hours, 80 ℃ bake 20 minutes to dry quickly. 7, using the time after adding hardener: 4-6 hours, expired please abandoned, the remaining ink can not be recycled. [Performance Test] 1,3M tape draw hundred grid test: 100% non-shedding 2, stamping resistance test: 1mm thick aluminum 180 ° bend unchanged. 3, anti-alcohol test: with cotton wool dipped in a concentration of 99% industrial alcohol 500G force level back and forth 200 times without bleaching. [Note] 1, the first Indian to comply with the requirements of a small test before mass production. 2, do the surface of the substrate to remove grease and impurities work to promote adhesion effect. 3, before the detection of adhesion, hardness, acid resistance, resistance to alcohol, detect chemical resistance, scratch resistance, abrasion resistance and other properties, we need to fully cured. 4, the case without permission, this series of inks and other types of ink may not mix and match colors. 5, ink, when the diluent and storage No smoking. 6, pay attention to good ventilation when using the construction site, try to avoid direct contact with the skin. 7, this product is accidentally splashed entrance, nose, eye, ear, apply plenty of water or direct medical assistance. 8. Technical Reference number as follows: Test item Test results of the test conditions of the ink line of ≤12um Fineness gauge dry gloss ≥65 ° 60 ° specular gloss meter drying rate table dry 25 ℃ × 5-10min or 60 ℃ × 2-3min hard work 25 ℃ 12Hr or 60 ℃ × 10min alcohol resistance No change 500 gf / cm2 alcohol cotton back and forth 200 times adhesion 100/100 1mm × 1mm × 100 grid 3M adhesive tape stripping Acid unchanged soak 5% HCI × 24Hr Alkali unchanged soak 5% NaOH × 24Hr salt tolerance unchanged soak 5% NaCI × 24Hr No change soaking water resistance 20 ℃ × 96Hr wear bottomless water 500 g / cm2 load sand eraser 200 round trip No change in heat resistance 80 ℃ × 12Hr The products are mainly used in screen printing and the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint surface and various ceiling oxide board, mirror panels, coated board, roller coated board and other products 2, product characteristics:.. light, good adhesion, fast drying, stamping resistance 3, diluent: with our B-03 special thinner or 783 open oil, washing network water cleaning screen with 718. 4, curing agent: one component use, can also choose to add our JS-10 special curing agent is used to increase the ink adhesion and physical and chemical resistance 5. , printing ink allocation methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity If you need to add curing agent, first add curing agent after mixing and set aside for 10 minutes, and curing agent for ink completely crosslinking. after dilution 6, the drying time:. dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly 7, adding curing agent after the use of time:. 4- 6 hours, expired please abandoned, residual ink Unrecyclable [detection] performance 1, 3M tape row adhesion test:. 100% without shedding 2, stamping resistance test:. 1mm thick aluminum 180 degree bend without change 3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500G stress level and back 200 times without decolorization. [note] 1, the first small try printing again after confirmation of compliance with the requirements of mass production. 2, do a good job in the substrate surface to remove grease and impurities, in order to promote the adhesion effect. Detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, abrasion resistance and other properties, Fully cured before detection. 4, without permission , may not use the series of ink and other types of ink mixing and matching. 5, ink, fireworks is strictly prohibited the use of thinner and storage. 6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin. 7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing or direct help doctor.