TDY oil-cooled electric drum electric drum YDY Flameproof oil-cooled electric drum

TDY oil-cooled electric drum electric drum YDY Flameproof when oil-cooled electric drum call, please make it clear that bandwidth and barrel diameter, according to what you said our bandwidth and Diameter to give you customized oil-cooled electric drum Description: oil cooling electric drum motor is driven, by continuously moving tape transport of various materials inside a new drive. Scope and features: 1, can replace the current widespread use of a motor reducer type of external drive means for constituting the belt conveyor can transport coal, ore, sand, cement, flour and other bulk materials, also can transport sack , equipment and other items into. 2, the structure is simple and compact, small footprint area. 3, sealed for dust concentration, wet and muddy in the workplace. 4, easy maintenance, safe and reliable operation and long life. 5, energy consumption, and easy to implement centralized control. 6, can meet a variety of check, brake, including plastic and other needs. 2 Working conditions 2.1 ambient temperature is a 15 ℃, + 40 ℃; 2.2 not more than 1000 meters above sea level, the temperature does not exceed 2.3 conveying material 60 ℃; 2.4 voltage 380V, frequency 50Hz. 3 basic parameters Diameter (mm) Power (kW) Bandwidth (mm) tape speed (m / s) Quality (kg) max 0.8 1.0 1.25 1.6 2.0 2.5 3.15 4.0 320 1.5 500???? 182 650???? 192 2.2 500??? 184,650??? 1,943,500?? 217,650?? 2244500? 224650? 2364002500???? 216,650???? 2,273,500???? 248,650?? ?? 2,624,500??? 253,650??? 267 500 1.5 500?? 269,650?? 280 2.2 500???? 271,650???? 282,800??? 3,123,500????? 299 650????? 313,800????? 3,434,500?????? 305,650?????? 319,800?????? 349 5.5 500???? 365,650??? ?? 401,800????? 430 7.5 650???? 414,800????? 44311650??? 476,800???? 51315800???? 53763031000? 52,641,000 ??? 5331200? 587 5.5 800???? 5,721,000???? 6,031,200????? 673 7.5 800???? 5,871,000????? 6,181,200????? 68,711,650 ?? 608,800??? 6,741,000?????? 7,061,200????? 77615800?? 6,921,000???? 7,241,200????? 794 ready 1 electric drum before use should not higher than 40 ℃ ambient temperature work under. 2 electrical control circuit should be installed with the choice of supporting the drum motor overload, single-phase operation and emergency brake and other protective devices, and make the body shell has a good grounding. All parts of the conveyor 3 shall be installed in accordance with the relevant provisions accurately, then you can conduct a trial run. 4 no-load and load test should be divided into two phases. No load, the machine should be running smoothly, no shock and large periodic noise. 5 Load after load test should test all normal. When commissioning, you should drive a car after the first feeding, and material uniform, continuous and slow to invest, parking should be preceded by stop feeding until the material before emptying parking. Production and use of a conveyor conveying ago, should be idle for a moment, to be operating normally before feeding. Place 2 material should be uniform, continuous, and avoid overloading. 3 production process should be avoided conveyor frequent starting and braking. 4 production staff should strictly abide by the rules, in order to avoid accidents. 5 Using the process, once a failure occurs, should immediately stop checks, be excluded. Maintenance 1 Maintenance 1 production process should be based on the nature of the material being conveyed, timely cleared to keep clean all parts of the conveyor. 2 electric drum change the oil every year and found the leak, check sealing parts, and replace worn seals. 3 inspection, adjustment, cleaning, etc. are not allowed in the functioning. 2 Maintenance Under normal circumstances, the drum motor repair once per year. The procedure is as follows: a drain hole left by the roller cover inside the drum of the lubricant clean emissions. 2 will roll open, the steps are: the left flange shaft junction box and the left seat and the left end cover bolts removed, and then the right end cover bolt and right seat removed, with the lifting rings on the right flange shaft It can be lifted out. 3 and the inner wall of the drum all parts of clean water. 4 again for the bearings (including motor bearings including a total of six), inject a sufficient amount of calcium sodium based grease. 5 Replace all seals and seal the motor and the drum body, the replacement of seals and seal must be intact, smooth the whole park, not the tiny bumps and depressions, can not have wrinkles, the material must be oil and rubber. 6 on the chassis and the motor winding insulation resistance between each other should not be less than 5 megohms, or should be dipping and drying. 7 Check the bearings, wear backstop and gear can not be replaced with. Instead the assembly step 8 should be open when the drum, by specialized personnel responsible for quality assurance. 9 into the drum into the new N46, oil, and liquid level reaches 1/3 cylinder diameter. 10 electric drum should work in accordance with test not higher than 40 ℃ ambient temperature, everything is normal can be put into the production of good quality, excellent price of electric drum where the election! The election to choose to go or choose Stephen! ! ! Good quality and reasonable price!