Gasoline Power Welder 200A XI'AN offer

200A Gasoline Power Welder 200A XI'AN offer preparation before use gasoline Power Welder Note 1, add oil (200A Gasoline Power Welder 1.5 liter gasoline Power Welder 1 liter of oil) Remember, do not add too much, or too little effect adds a life, can not even start. 2, add fuel, check whether the battery wire 3 having received prison immediately start; (200A Gasoline Power Welder throttle switch should be in filling state (right), then press and hold the power key on top of the valve twist the ignition seconds bell simultaneously release valve and ignition key), after closing down is the key to press the red button switch below the throttle after throttle release natural stop, start again, be sure to add a good throttle switch. Gasoline welder start, first of all should be open throttle (air filter above the throttle lever to pull out), and then directly twist the ignition key to start, after starting the first time the throttle is closed (throttle lever we must act in) 5, Welding current switch should remain open when the machine maximum working DC regulator switch must twist to the maximum. Use electric welding machine when it is best not to use other appliances, if necessary use of electrical appliances if they would wondering whether we can use. 6, welding quick joint to qualify for the provisions is the use of 35 square feet or more, or 50 square Doppler line, (too bad, too small will burn, predetermined length is less than 8 meters, in principle, can be more than 10 meters, remember If the output line connected too long will affect the use quality, can cause black smoke, the card machine, or even shut down and so 7. welder Red quick connector interfaces are connected to the torch (welding clamp), black lead is connected to the ground, remember , then the wrong can not normally use gasoline Power Welder 200A 200A XI'AN offer gasoline use electric welding machine parameters: Model KZ200AE welding configuration: Rated current 190A current range 50-190A electrode diameter ￠ 2.5 ~ 4.0 generation Configuration: Rated power 5.0KVA Rated frequency 50HZ Rated voltage 220V Phase Single engine configuration: Displacement 439cc four-stroke single cylinder air-cooled type Maximum output power 12.5 / 3600Kw / rpm Oil Capacity 1.1L Starting method Hand / electric start Fuel 90 # unleaded gasoline unit: Dimensions (L * W * H): 69 * 54 * 56.5cm NW / GW (KG) 80 / 85KG 200A Gasoline Power Welder 200A XI'AN offer gasoline Power Welder Keywords: 200A gasoline Power Generation Welding | 200 Ann gasoline Power Welder | Power Welder manufacturers | Power Welder Quote | Power Welder manufacturers | Power Welder Price | Power Welder Suppliers | Diesel Power Welder | Gasoline Power Welder | normal gasoline welding power Welder |.. 200A Gasoline Power Welder as a power plant for six months or longer if not using electricity King Power Welder Please make the following preparations before storing a can of gasoline to electric welding 200A machine kept in a well-ventilated, low humidity area. 2, disconnect the fuel line, and then carefully put the fuel tank and filter (Cup) discharge of residual oil. Gasoline will long remain in the fuel tank fuel tank damage , will start causing trouble again. 3, can loosen the drain screw on the carburetor float chamber to drain the fuel to the carburetor or the device up and running in no shape under load until it ran out of fuel stops. 4, disconnect the battery terminals. Then check the position of saving the battery liquid, if necessary, then please fill distilled water. 5, change the oil. Used oil can produce a lot of waste, will not produce long-term parking lot of sediment If re-use will be the loss of the engine part. 6, if there are loose screws and bolts between the inspection and, if necessary, be tightened. 7, using carefully with oil cloth to clean the machine. If necessary, you can spray preservatives. Do not use water to clean off. 200A XI'AN offer gasoline Power Welder