Fraternity County Qinyang Mengzhou County PE pipe | Mengzhou PE drainage pipe

Fraternity County Qinyang Mengzhou County PE pipe | Mengzhou PE drainage pipe | PE pipe irrigation Mengzhou Luoyang State-run specialized in the production of new material PE pipe, HDPE pipe, widely used in the field, is widely used in municipal water supply and drainage, irrigation, rural drinking water delivery, the mine water system, has begun to replace the old sewer line in the past, Luoyang State-run production of new material PE pipe model is complete, DN15-1400, factory outlets, cheap. Also the intention of customers welcome to visit Luoyang. 2015 Kazuo rural drinking water safety plans 14 new water wells play, 22 old wells transformation, network extension 5, the new well house 9, 36 sets of matching pumps, disinfection and purification equipment 27 units, built in storage 2 pools, water supply frequency microcomputer seven, buried pipe network 96.75 km, 2.3 km erection and low voltage lines. Project started on January 25, as of now, started 15 water wells, completed seven, eight in the construction, engineering and strive to be completed in October. Fraternity County Qinyang Mengzhou County PE pipe, PE pipe drainage position in the application of increasing: PE pipe drainage pipe as a new kind of species, not only high strength and simplicity of construction, the joint security, impact resistance, flexibility Well, is widely used as a municipal water supply pipeline, fast market growth. PE pipe has low density, strength and quality is high and the temperature of brittle to low, good toughness, good corrosion insulation, easy to color, such as construction and easy to install, which is widely used in municipal and building water, gas, heating heating, cable threading, agricultural water-saving irrigation and industrial sewage, mining and mineral transportation and other fields. Fraternity County Qinyang Mengzhou County PE pipe, PE drainage tube model table: Ф32 * 3.0mm * 1.6MP, Ф40 * 3.7mm * 1.6MP, Ф50 * 4.6mm * 1.6MP, Ф63 * 4.7mm * 1.25MP Ф63 * 5.8mm * 1.6MP, Ф75 * 4.5mm * 1.0MP, Ф75 * 6.7mm * 1.25MP, Ф75 * 6.8mm * 1.6MP Ф90 * 4.3mm * 0.8MP, Ф90 * 5.4mm * 1.0MP, Ф90 * 5.6mm * 1.25MP, Ф90 * 8.2mm * 1.6MPФ110 * 4.2mm * 0.6MP, Ф110 * 5.3mm * 0.8MP, Ф110 * 6.6mm * 1.0MP Ф110 * 8.1mm * 1.25MP, Ф110 * 10.0mm * 1.6MP, Ф125 * 4.8mm * 0.6MP Ф125 * 6.0mm * 0.8MPФ125 * 7.4mm * 1.0MP, Ф125 * 9.2mm * 1.25MP Ф125 * 11.4mm * 1.6MP, Ф140 * 5.4mm * 0.6MP, Ф140 * 6.7mm * 0.8MP Ф140 * 8.3mm * 1.0MP, Ф140 * 10.3mm * 1.25MP, Ф140 * 12.7mm * 1.6MP fraternity County Qinyang Mengzhou County PE pipes, PE pipes and drainage on the application should pay attention to the drainage 1. PE When the pipe is installed, if the operation is too small (eg: tube wells, the ceiling construction, etc.), should be fused type connection. 2. seasonal outdoor PE pipe laying drainage, there is sunlight, and recommends measures shelter. 3. PE drainage pipe, DN≤110 piping installation can be a little snake laying summer, DN≥110 pipeline because there is sufficient soil resistance, resistant to thermal stress, no reserve tube length; in winter, was not required to pre- leaving the tube length. 4. When Butt connection requires a voltage between 200 ~ 220V, if the voltage is too high, it will cause the heating plate temperature is too high, the voltage is too low, then the docking unit is not working properly; PE pipe butt drainage should keep interface aligned, or will cause the docking area is not enough request, weld strength is not enough, and not into curling; heating plate heating pipes clean interface untreated or heating plate with oil, sand and other impurities, may cause disengagement interface leakage; heating time to control the heating time is short, the pipe absorbing enough time, will cause the weld bead is too small, the heating time is too long, it will cause the weld bead is too large, it is possible to form a Weld. 5. melt socket connection, the heating temperature is not too high, too long, the temperature is best controlled at 210 ± 10 ℃, otherwise it will cause excessive internal fittings lava extrusion, reducing the inside diameter through the water; when the socket fittings or pipe interface should be clean, otherwise it will cause leakage disengage socket; Also, pay attention to the drainage control the angle and direction of PE pipe to avoid rework customers are interested in, welcome to visit our factory, and we look forward to you! Contact: Manager He Tel: 0379-65260623 18638366105 Company Website: www.grcgg.com www.lyjhgy.com www.cn-csg.com Address: Luoyang City area in the West Valley Road, No. 72 Riverside Building Plant Address: Luoyang Mengjin County, Zhejiang Industrial Park City Ma Tun Sales Department Address: Luoyang City, the area of ??King City Avenue 111 Information Technology, Luoyang City