PSM-E01

PSM-E01 PSM-E01 System Overview PSM-E01 monitoring system includes HD Series charging module internal monitoring circuits, and monitoring module (PSM-E01), in addition the system may also be accessed from the external insulation monitoring relay inside (monitoring module has a simple ground voltage monitoring function), fault information to be output node stem cell detector and other equipment. PSM-E01 monitoring system is mainly designed for co-manufacturers, which is part of the small capacity of the current system configuration can be applied to the following 35kV substation and a variety of low-end users become DC operating power systems. HD series with high-frequency switching power charging module, PSM-E01 monitoring system can complete intelligent battery management and DC systems and alarm monitoring. PSM-E01 monitoring system with remote management capabilities, you can choose to report data through Modbus, CDT91 communication protocols and integrated automation systems for power plants to achieve unattended. Semaphore PSM-E01 monitoring system monitoring system to monitor various analog and digital, display, or an alarm on the PSM-E01 PCU LCD screen. Function monitoring module is a data processing center monitoring system, collecting a variety of voltage and current data, and complete automatic battery float conversion by controlling the HD series rectifiers. The specific functions are as follows: Alarm Function: If the power generation system failure, the monitoring module will pop up warning message menu, the alarm indicator lights, while controlling the alarm buzzer. Remote control, remote telemetry functions: power system monitoring module can also run the data through RS485 or RS232 communication interface according to user-defined communication protocol (optional Modbus or CDT91) reported to the integrated automation systems and integrated automation system receives issued are floating control commands to achieve remote control, telemetry, remote functions. Display: LCD display, with the front panel buttons, set to be completed, access, display functions, event records. Appearance PSM-E01 PCU customs front panel includes two LEDs, a reset button, an LCD display and six function keys. Power indicator and alarm indicator lights. When normal power monitoring module, power indicator light, otherwise, the power LED off. When there is an alarm monitoring module, alarm indicator light, otherwise, light off. After pressing the reset button, the monitoring module will restart. After the monitoring module for system-level parameter settings, you need to press the reset button to restart the monitoring module to save the system-level parameters. LCD screen can display four lines of eight characters can be displayed. Electric power system is used to display information and alarm information all the work. Flip function keys for menu operation, and enter the number, and parameter settings confirmation. Rear panel panel includes a rear cover, two rows of terminals, two ground nuts (which for insulation testing ground nut P1, P2 for monitoring module chassis ground nut) and four mounting screws. Select the device list when monitoring module PSM-E01 and PSM-E02 monitoring module, must Remarks monitoring module PSM-E01 1 02311419 Emerson RS232 / 485 communication port monitoring module PSM- containing device configuration from our model specification Quantity BOM code name manufacturers E02 1 02311435 Emerson-free communication port monitoring accessories MONI01FJ 1 02233166 Emerson temperature sensor MONI01ZSL 1 04115949 Emerson switch a DC output breaker status fed a normally closed switch signal outside all merged into one signal input 2 Battery fuse status NC battery fault state 3 input fuse blown insulation relay alarm status normally open relay detection of external insulation of insulated busbars 4 AC CB trip alarm signal NC AC DC system total input switch status or trip signal 5 cell abnormalities C-level output signal of a mine status signal audible alarm signal normally closed state inspection detected external battery cells and batteries Group 6 SPD fault signal NC AC DC system total input of 1 12Vdc drive voltage, it is recommended use two 12V piezoelectric ceramic buzzer alarm indicator signal 1 12Vdc drive voltage, recommended type of alarm indicator light-emitting diodes, the color is yellow 3 1 alarm relay output contact capacity: 220Vdc / 300mA, 250Vac / 1A. Alarm systems of dry node output can be combined into this one signal output 4 2 with RS232 serial communication port or RS485 serial port two kinds of external communications, but not both. All analog and digital computer can be output to the background via the serial port. Communication protocol is Modbus protocol or CDT91 a battery management functions according to float conversion parameters set by the user, are floating automatic battery management, limiting charge management, temperature compensation, battery capacity test. Manual can be a maximum 48 hours of operation are charging two batteries are charged to protect user settings automatically BC protection time to complete all of the battery charge and overcharge protection manual are different auto BC protection time, the need to set the system in accordance with an exception 3 alarm float switch disconnected battery shunt load disconnection shunt current sensing shunts disconnect the battery fuse damaged or broken wires, AC CB trip, fed a CB trip, SPD fault alarm, battery monomer abnormal alarm when selecting external bus insulation decline represented insulation insulation testing alarm relays; built-in insulation testing when choosing representation of PSM-E01 detects positive and negative bus to ground pressure gauge Fuzhou Ding Hui Electric Co.'s business QQ : 1157363036 Enterprise Hotline: 18150039331 official website: www.fzdsh.cn Emerson I also sell other products can take Taobao and Alibaba follows: http://400654321.taobao.com/ http://fzdshdq.1688.com