10SA-6 10SA-6A 10SA-6B Xi'an SA in a pump in a pump factory direct

10SA-6 10SA-6A 10SA-6B in the open in a pump factory direct Xi'an SA pump 10SA-6 10SA-6A 10SA-6B Xi'an SA in a pump in a pump factory direct (0-7-3-1-8-5 -0-1-8-1-8-4) SA in a pump manufacturers promise: Where Our products under normal use, the shelf life of the machine within 12 months after leaving the factory, the shelf life of wearing parts factory within six months of shelf life of the mechanical seal within three months after leaving the factory. Service time: I plant will respond within 48 hours by our equipment failure occurs during the warranty period, service to the scene after receiving the notice within three working days. 10SA-6 flow 432-540-720m3 / h Head 96-94-89m speed 1480r / min Power 250KW 10SA-6A flow 432-540-720m3 / h Head 85.3-84-76m speed 1480r / min flow power 220KW 10SA-6B 432-540-720m3 / h Head 76.4-74-67m speed 1480r / min Power 185KW 10SA-6J flow 600-500-400m3 / h Head 35-39-42m speed 980r / min Power 90KW 10SA-6JA flow 300-400- 600m3 / h Head 36.8-36-33m speed 980r / min Power 75KW 10SA-6JB flow 300-400-500m3 / h Head 33-32-28m speed 980r / min Power 55KW 10SA-6F flow 500-600-650m3 / h Head 65.6-62.6-60m speed 1480r / min power 160KW structure type pumps are horizontal installation, the pump casing in the horizontal axis to separate the upper part of the pump cover, the lower part of the pump, the inlet and outlet of the pump at the bottom of the pump axis on the body, its center line perpendicular to the axis, and maintenance without disassembly water outlet road, you can uncover the pump cover, remove the rotor parts. Seal can be soft packing seal and mechanical seal. Direction of rotation from the motor to the pump to see, pump counterclockwise rotation, the suction on the left and the right outlet. Pump is clockwise rotation, ie suction around, outlet on the left. According to customer requirements will drive end to another end of the pump, this time, steering and inhalation outlet direction contrary to the above-average. The main parts of the material pump flow components are made of cast iron, such as user needs, the impeller can also be cast steel and brass, but it must be indicated on the order contract. Complete range Complete supply of pumps, motors, couplings. Pump inlet diameter ≤200mm with public base, the rest do not deserve the base. Please specify when ordering material of main parts, if the pump motor have special requirements, in consultation with the relevant technical requirements of the company. Structure Description 1, a suction port and a discharge port SA pumps are cast on the pump body, a horizontal direction, perpendicular to the axis. When the level of separate pump and pump cover to expose the cover to check the internal parts without dismantling the piping and electrical (or other prime mover). From the drive end look, SA in front of the pump shaft models are counterclockwise rotation, S.SA are clockwise in the middle of the shaft models. 2, the main structure of this model in addition to the bearing member and the bearing have several different structures, the other portion of substantially the same. Bearing parts: some pump ball bearings, lubricated with oil or grease stains cup ring splash oil lubrication; some pump oil tile inlaid alloy plain bearings, end the installation of single row radial ball bearings. Double suction pump axial force is essentially balanced, partially balanced axial force, with the single row radial ball bearing. Sleeve structure: some bushes with a threaded nut to secure the impeller doubles; some pumps at both ends with two sleeves, one with a thread; besides some pump sleeve, the other with a sleeve nut, a fixed sleeve and impeller. 3, the pump main parts: pump and pump cover, impeller, shaft, seal rings, bushings, bearings body, bearings, packing sleeve and packing ring. In addition to the shaft is made of steel with high-quality carbon steel, bolts, screws, nuts, keys and other parts, most of the other parts of the pump are made of cast iron. Special circumstances, flow components or other components can also be used stainless steel, steel, copper and copper alloys, ductile iron corrosion and other wear-resistant material. Pump seal ring and is located in the hub of the filler section, are wearing parts, replace worn parts availability. Bearing part of the oil cup if fitted with a calcium base lubricating oil, where oil ring splash oil lubricated bearings, with the 2nd or the 3rd spindle oil lubrication. 4, packing with packing sleeve, packing rings, gland and other components. Tightness of filler, must be appropriate, in order to be able to drop by drop liquid oozing appropriate, the sleeve tight easy to heat, too much loose the fluid loss will reduce the efficiency of the pump. Related literacy: ?????? Points ------------ pump pumps used widely used (pump), such as centrifugal pump, submersible pumps, Francis pumps, etc. Power Machinery and pump power exists in the use of matching unreasonable, burn-in, energy-consuming large, the problem of higher repair costs. Resulting in a waste of manpower, material and financial resources, increasing the economic burden on the user. For this reason, everyone in the use of the pump, you need to pay attention to the following aspects of the problem. A supporting force power and pump (pump) rated power to match. Generally how much a water pump kW auxiliary power on the pump nameplate are clearly defined. If not complete, dynamic power is too big, it will cause a "big horse cart", wasting power, increased costs; on the contrary, there will be "small horse-drawn carts," water flow inadequate or overloaded, damaged parts unable to work, wasted investment. Second, the new machine starts pumping, first wipe off the oil pump shaft protection and other part. Carefully check whether the normal rotation of the impeller, shaft rotation is flexible, bearing clearance is appropriate, see the gasket between the pump is damaged joints, each component connection is solid, water hose leak watertight, leak and so on. If problems should be promptly repaired. Third, pumps and power machinery installed firmly. To achieve particular pump shaft parallel with the axis of power machine; when installing the belt, the belt should pay attention to the loose side to be on in order to facilitate increased transmission efficiency. Four motor car driven pump the water when two pumps at the same time start the job prohibited to prevent the entire line current is too large, and burn out the motor, causing undue economic losses. Fifth, we should promptly check the pump inlet valve underwater, whether blocked weeds. Note the flow head meets the performance requirements. Upon discovery of the problem, they should immediately be excluded to ensure normal operation. Six, when the pump stops pumping, you must first close the pressure valve, and then stop the operation, the belt unloaded. When long time without stopping, the machine should be carefully cleaned, the water within the pump completely discharged. The machine easily corroded parts and spare parts, are coated with protective oil to prevent rust bad water pump.