XLLS-II 5A [rope-way switch]

XLLS-II 5A] [rope-way switch for manual reset type II, high safety performance camshaft angle to go back to self-locking position, after the need to manually reset the handle cam can only return to the original state. The device uses a waterproof, dustproof seal design, better prevent water, dust gets inside the casing. Standard cable switch protection class NEMA4 adapt to indoor or outdoor installation. FM Approved for switching secondary class 1 E, F and G groups. Specially treated surface can be used for saline, alkaline or acidic region. For corrosion particularly serious regional surface using electroless nickel. Our factory specializes in the production of conveyor equipment, good service, quality and security, delivery speed, a lot of cash. Integrity of business e-commerce transactions. Two deviation switches, rope-way switch, speed detectors, slip switch, belt slip detection device, level monitors, speed detectors, less speed switch, switch heap of coal, coal flow switch, tilt switches, tear switch , belt conveyor system control cabinet, mine sound and light alarm, borehole magnetic switch, sound and light combination of signal devices and other automated industrial appliances. Features? Simple and practical structure, reliable performance, dustproof, shockproof and moisture? Small size, light weight, long life, easy installation, maintenance-free? The output signal can interlock with field devices, can also be served on the automatic control system ? Power adaptability: 24 ~ 380V Technical parameters Installation instructions 1, rope switch installed in pairs of left and right sides of the belt machine, belt conveyor in the corner next to the hob Ф12mm holes drilled with M10 × 40mm bolt rope switch. 2, rope switch installed a station every 40 meters, its location should be below the belt and easy on-site staff. 3, tied a rope off the arm, covered steel wire rope drawstring recommended, 3 ~ 5mm in diameter can be. Rope clamp with rope, about three meters to install a ring every care to avoid excessive deflection hanging rope, the rope to ensure reliable operation. Under the premise of working to meet the switch, as taut rope, wire rope hanging reduce deflection. 4, for climbing belt segment, should try to shorten the rope switch spacing, and the rope length. I plant the rope-way switch models introduced: KLT2-1, HFKLT2-1, HFKLT2-I, KLTZ2-2, KLTZ2-1, HFKLT-II, HFKLT2-II, HFKLT2-11, HKLT2-2, KLT2-11 , KLT2-1, KLT2-II, XLLS-I, XLLS-II, XUS-II, XLLS-11, XLLS-2, DLS-I, DLS-II, DLS-11, DSL-II, DSL-11, DSL -2, DSL-1, DSL-I, HFKLT2-2, KLT2-2, YHLS-I, YHLS-II, YHLS-11, YHL-4, YHLS-4, GHLS-I, GHLS-II, GHLS-11 , TYSLY2-1, TYSLY2-2, TYSLY2-II, TYSLY2-I, KST-2, FKLT2-Z, FKLT2-Y, FKLT2-II, FKLT2-2, KLT2-P-II, KLT2-PI, XYXL-A , NST2-II, NST2-I, HZ-KLT2-11-S, NST-1, NST-2, SLFB-II, SLFB-I, NKLS-I, NKLS-1, NKLS-2, NKLS-II, DFLS -II, DFLS-I, PMII, YWLX-II, DCX-K-1, DCX-K-2, DCX-K-II, YWLX-I, YHL-II, YHL-11, YHL-I, YBLK-KLT2 , HFKLT2-S1, HFKLT2-S2, HFKLT2-Z2, KLT2-S2, GYLS-II, GYLS-11, GYLS-I, GYLS-I-2, GYLS-1-2, GYLS-II-2, GYLS-2 , YHL-2, YHLS-2, JYB / KS-1, WHKL-II, WHKL-I, YBLX-KLT2-1, YBLX-KLT2-2, YSLS-1, YBLX-KLT2-II, BLKT2-II, YF -BLKT-I, YF-BLKT-II, BLKT2-11, YLXA-10A, BKT2-II, BKT2-2, BKT2-1, BLK-2, BLK-1, LS-I, LS-II, XTD-PK , THFL-2, THFL-II, LS-1, LS-11, LS-2, DLX-K2 / D, DLX-K2 / J, JLK-AI, JLK-A-II, JXW (KLT2) -I, JXW (KLT2) -II, HFRLB-11, HFRLB-2, HFRLB-1, HFRLB-II, KSD-II, KSD-2, KSD-1, XJM / KS-II, KLT2-N1, JX (KLT2) - 2, GRB-17088, GRB-19150, GRB-19670, XTD-LS, XTD-ZL-B, XTD-SH, FPK-AK, DLX-KTC / LS, BLK2-11