6SA-6 6SA-6A 6SA-6J in the open in the open centrifugal centrifugal Xinyu SA in the open centrifugal pump manufacturers

6SA-6 6SA-6A 6SA-6J in the open in the open centrifugal centrifugal Xinyu SA in the open centrifugal pump manufacturers 6SA-6 6SA-6A 6SA-6J in the open in the open centrifugal centrifugal Xinyu SA in the open centrifugal pump manufacturers (0 -7-3-1-8-5-0-1-8-1-8-4) SA-type single-stage, double-suction centrifugal pumps, adapted to the factories, cities, mines, power plants, farms, water conservancy and other fields. Delivery of solid particles in water or physical and chemical properties similar to water, other liquids, is the transmission medium temperature 0 ℃ ~ 80 ℃. Maximum allowable inlet pressure 0.6mpa flow parameter range: 72 ~ 100800m3 / h Head:? 11 ~ 140m sA Model Description 10SA-6JA 10- by 25-caliber addition to inhalation of water (ie, inlet diameter of 250mm) SA- single-stage double suction horizontal centrifugal pumps? 6- specific speed is about 10 integer addition of? J- represents rated speed change? A- represents the first change in impeller diameter, a, b, c ...... and so on structural type pump horizontal installation, the pump casing in the horizontal axis to separate the upper part of the pump cover, the lower part of the pump, inlet and outlet are on the bottom of the pump casing axis, its center line perpendicular to the axis, without disassembly overhaul inlet and outlet road, you can uncover the pump cover, remove the rotor parts. Seal can be soft packing seal and mechanical seal. Direction of rotation from the motor to the pump to see, pump counterclockwise rotation, the suction on the left and the right outlet. Pump is clockwise rotation, ie suction around, outlet on the left. According to customer requirements will drive end to another end of the pump, this time, steering and inhalation outlet direction contrary to the above-average. The main parts of the material pump flow components are made of cast iron, such as user needs, the impeller can also be cast steel and brass, but it must be indicated on the order contract. Complete range Complete supply of pumps, motors, couplings. Pump inlet diameter ≤200mm with public base, the rest do not deserve the base. Please specify when ordering material of main parts, if the pump motor have special requirements, in consultation with the relevant technical requirements of the company. Structure Description 1, a suction port and a discharge port SA pumps are cast on the pump body, a horizontal direction, perpendicular to the axis. When the level of separate pump and pump cover to expose the cover to check the internal parts without dismantling the piping and electrical (or other prime mover). From the drive end look, SA in front of the pump shaft models are counterclockwise rotation, S.SA are clockwise in the middle of the shaft models. 2, the main structure of this model in addition to the bearing member and the bearing have several different structures, the other portion of substantially the same. Bearing parts: some pump ball bearings, lubricated with oil or grease stains cup ring splash oil lubrication; some pump oil tile inlaid alloy plain bearings, end the installation of single row radial ball bearings. Double suction pump axial force is essentially balanced, partially balanced axial force, with the single row radial ball bearing. Sleeve structure: some bushes with a threaded nut to secure the impeller doubles; some pumps at both ends with two sleeves, one with a thread; besides some pump sleeve, the other with a sleeve nut, a fixed sleeve and impeller. 3, the pump main parts: pump and pump cover, impeller, shaft, seal rings, bushings, bearings body, bearings, packing sleeve and packing ring. In addition to the shaft is made of steel with high-quality carbon steel, bolts, screws, nuts, keys and other parts, most of the other parts of the pump are made of cast iron. Special circumstances, flow components or other components can also be used stainless steel, steel, copper and copper alloys, ductile iron corrosion and other wear-resistant material. Pump seal ring and is located in the hub of the filler section, are wearing parts, replace worn parts availability. Bearing part of the oil cup if fitted with a calcium base lubricating oil, where oil ring splash oil lubricated bearings, with the 2nd or the 3rd spindle oil lubrication. 4, packing with packing sleeve, packing rings, gland and other components. Tightness of filler, must be appropriate, in order to be able to drop by drop liquid oozing appropriate, the sleeve tight easy to heat, too much loose the fluid loss will reduce the efficiency of the pump. 6SA-6 flow 126-180-216m3 / h Head 104-97-87m speed 2980r / min Power 75KW 6SA-6A flow 119-170-204m3 / h Head 91-84.5-76m speed 2980r / min flow power 75KW 6SA-6J 72-90-108m3 / h Head 24-22.5-20m speed 1480r / min power 11KW Our promise: Where Our products under normal use, the shelf life of the machine within 12 months after leaving the factory, wearing parts Shelf life of the factory within six months, the shelf life of the mechanical seal within three months after leaving the factory. Service time: I plant will respond within 48 hours by our equipment failure occurs during the warranty period, service to the scene after receiving the notice within three working days.