Skeleton electrical cabinets, appliances skeleton, roll forming machine equipment, sell full-automation Tianyuan skeleton production line equipment electrical cabinets

Just below the skeleton of electrical equipment production line reference materials, specifically customized according to customer requirements 1. Equipment Technical Requirements 1.1 Equipment Technical conditions: 1.1.1 area: 28 × 3.0 × 2.5 (length × width × height) meters. 1.1.2 feed direction: left right out. 1.1.3 voltage parameters 380V, 50Hz, 3 phase. 1.1.4 Hydraulic oil: 46 # hydraulic oil. 1.1.5 gear oil: 18 # hypoid gear oil. 1.2 Main technical parameters 1.2.1 rolled strip width: 70 ~ 150 mm 1.2.2 rolled strip thickness: 2mm 1.2.3 rolled strip material: low carbon steel, such as Q195, Q235. 1.2.4 Rolling workpiece length: 1500 ~ 4000mm 1.2.5 equipment installed capacity: about 37KW. 2. Rolled Products range 2.1 forming units can be rolled thickness was 2mm mm. 2.2 3. Size supplier of rolled products and services 3.1 device provisions of the contract's scope of supply No. Name equipment models and specifications Number of motor power (KW) Note 1 discharge machine MT-200 1 Taiwan 2 leveler HS-200 1 set of 33 sets of hydraulic punching servo feeder 1 1.8 1 set of hydraulic punching machine punching mold forming a set of four hosts GY150 type 1 18.5 5 sets of 2 sets of mold Note: installed in the same axis cutter YQ400X3Z 1 6 5.5-7 material platform SL-400X4000 1 8-electrical control system 1 set 9 C profiles Angles hydraulic machine 4. Device structure Performance Overview passive discharge - leveling, feeding - Continuous punch Bottom - Forming - length, cut - 4.2 Receipt of major equipment structure, Performance Overview 4.2.1 Piggyback discharge machine structure: Passive discharge. Sheet width: 70 ~ 150mm; Material thickness 2mm; roll inside diameter: φ508mm; inner diameter sizing range ф480-520 mm; maximum outer diameter roll: φ1200mm; Bearing weight: 2T 4.2.2 leveler work rolls a few. : Five roller leveler b Features: leveling roller quenched after chrome handle its rigidity, surface roughness greatly improved mechanical properties; it by pinch rollers and leveling rollers, pinch rollers can be used alone. adjustment, leveling roller with the overall structure, before and after the establishment of two adjustment points, can form a certain angle, easy to improve the quality of leveling. Leveler infeed end with a pair of guide rollers and two pairs of flat vertical guide rollers, guide the vertical roll can move and move simultaneously. Handwheel adjustment with scale, facilitate this. Leveler are cited around the bridge devices with material. Located between the leveler and feeder live photoelectric signal, the feedback signal is emitted into the control system, control system sends commands to the variable frequency motor speed to control the storage capacity of the reservoir area of ??the strip material, to achieve continuous leveling purposes. Motor configuration: 380V 3KW 4 pole correction rollers: 3/4 ring material leveling range: maximum material width of 200mm, the maximum thickness of the material (steel) 1.5mm 4.2.3 punching a function of the servo feeder: Feeding b Structural Features: servo motor drive -2.2KW. Multi-stage feeding: You can enter 10 different sets of feed length, each providing 999 times more punches. LCD touch display for easy change significantly, setting the technical parameters. Auto-sensing system and start punching linkage (control punch start). Motor configuration: 380V 1.8KW 4-pole, air compressors need to reprovision. (Flow rate of 0.5m3 / min; pressure of 0.6MPa servo feeder feeder for punching machine punching way: Four-column hydraulic press die Material: Cr12 Quantity: 1 set 4.2.4 forming host models: GY150-molding machine. Frame: cast iron arch rack + chain drive maximum feed width:. 150mm maximum material thickness: 2mm roller Shaft diameter: φ65 mm, 45 # steel quenching roll mold material: GCr15, quenching, HRC58-62 ° molding passes: 14 (C profile) main drive motor: 18.5kw inverter motor drive 4.2.5 cutting machine a, cut way: stop hydraulic cutting b, cavity-type cutter knives Material:. Cr12MoV C, the number of tools: 1 4.2.6 sets out the material platform structure: Drum roll, unpowered 4.2.7 entire line electrical control system with PLC control, LCD touch screen, human-machine interface (for reference only).