ZY-1104AB

Anti-stick back super soft mortar manual feature super soft (softness is 3 to 5 times the imports of similar products! Fabric itself does not affect the basic feel!) Super anti-stick back (after 8 hours to dry the surface in contact with the skin or both pulp layer on the surface of each other are not feel any pressure stickiness) not covering power plug network + + + does not move antifreeze color A white glue film after a slight touch (softness is 3 to 5 times the imports of similar products time!) B transparent pulp film after no feel (without affecting the softness of the fabric itself) A white glue and paste transparent interworking using B, B more transparent printed feel softer pulp ratio. Appearance and composition A Appearance: white viscous paste. Components: the polymer emulsion and titanium * components. B Appearance: milky white viscous paste. Composition: polymer application reference tone dark colored hue A white glue 10 ~ 30% A white glue 70 ~ 80% B transparent pulp 70 ~ 90% B 20% to 30% transparent paste paste paste X X% % dry naturally after 48 hours you can print high-temperature-resistant to 600 washing two hours. Failure and exclusion: a poor firmness caused about six kinds of possibilities: one, not a cotton fabric, fabric is smooth, soft silicone residue or cloth too Solution: replace or add optional nylon pulp from 1 to 1.5% . FY-1002 catalyst 2, cloth hair too ANSWER: India 4-6 knives force when India first plate (use a hard side cutter ideal), or you can use the iron to flatten or wool cloth backing transparent pulp two times and then printed white glue or other colors. 3, humid weather, plasma surface is not fully dry answer: 150 degrees or 150 degrees bake 1 minute 10 seconds Pressing. 4, increase the amount of paste over more than 10% Solution: increase transparency to reduce the weight of the slurry paste used in a proportion (eg: can be individually adjusted with pure transparent black). 5, the pulp layer does not dry hot Pressing answer begins: pulp layer dry naturally be more than 8 percent and then pressed hot. (Explanation: The plasma layer is dry starts Pressing likely to cause blistering, the slurry layer and pulp layer separation) 6, when more than four kinds of situations do not exist, but also mainly the firmness there any solution? Solution: Add 1 ~ 3% FY-1002 can be a catalyst to enhance the firmness of 1 to 3 times. Second, what appears resilient enough to have caused several reasons? 1, plus the amount of paste over more than 10% Solution: Increase transparent pulp to reduce the weight ratio of the amount of paste. 2, plasma layer is too thin ANSWER: When one or more printed paste printing received lighter intensity, as the pulp layer remains thick. 3, white glue and transparent pulp ratio of disproportionate answer: increase transparency pulp weight can significantly improve the elasticity of the pulp layer. 4, wove deep, extremely elastic fabric itself answers: first with transparent pulp hit bottom 2 to 3 times, each printed three knives, and then printed white glue or other colors. 5, add too much weight catalyst answer: proper control weight of the catalyst, as long as the firm would not have to meet the requirements of the increased amount of the catalyst. Third, feel hard or uneven surfaces which have caused several reasons? 1, rough cloth surface itself answers: first with transparent pulp hit twice at the end, and then printed white glue or other colors. 2, pulp consistency is not enough to answer: not enough consistency pulp can add a thickener to improve its consistency (explanation: pulp consistency is not enough to easily penetrate cloth at the end, so obviously feel hard and the surface is not smooth) 3, paste more than 12 percent increase over the amount of answers: transparent pulp weight increase dosage to reduce the proportion of paste, which can significantly improve the softness of the pulp layer. Fourth, anti-stick surface causes and prevention? 1, the plasma layer on the surface does not dry answer: 150 degrees or 150 degrees bake 1 minute 10 seconds Pressing. Five, hiding enough reasons: 1, the ratio is too transparent pulp Answer: transparent cytoplasm ratio appropriate adjustments. 2, the slurry is too thin to answer: too thin slurry can add some thickening, stir it to improve consistency (explanation: When printing out pulp slurry layer is relatively thin too, so there will be enough of hiding case) Brand: India Manufacturer: India Company stored at room temperature shelf life of six months.