Schneider Merlin Gerin battery M2AL12-150

? Schneider Merlin Gerin Schneider Merlin Gerin M2AL12-150 batteries battery M2AL12-150 agents 010-57416568 15340070875 MGE battery structural features elongated structure design: single arrangement for 2 × 3 structure, conducive to heat;? positive plate: pasted positive plate, hot and humid 4BS curing process, the battery has a good cycle life; placed in front of the terminals:? installation, connection, easy maintenance; the front of the exhaust system focused on:? the battery internally generated outdoor gas discharge battery; flat plug-in terminal protective cover:? to prevent a short circuit, protective cover detection hole located conveniently voltage measurement; partitions:? special fiber thickness ratio of AGM separator to improve the suction height; battery shell? : impact, shock-resistant high-strength ABS (optional flame retardant) thick design; Terminal Seal:? the use of multi-pole sealed proprietary technology. ups battery installation considerations when installing ups batteries, there are many considerations, let's do the detailed analysis: 1, according to the vertically upright placement principle, prohibit the use of ups battery upside down. 2. Do not give abnormal vibration and impact on the ups batteries. 3, during the installation process should pay attention to insulation. 4. Do not install the machine into a closed-shaped structure. 5, the installation process should pay attention to make to maintain a certain distance between the battery, in order to ensure air circulation. 6. Please do not mix different kinds of ups battery use. 7. Do not let the ups battery contact with organic solvents. MGE battery use and maintenance methods are what MGE battery use and maintenance methods are needed to grasp, although the use of maintenance-free battery does not require special maintenance work manually, but when you use or have certain requirements If used improperly affect battery life. The following is an analysis of MGE battery use and maintenance methods made. MGE battery use and maintenance methods: 1) Install the battery should be installed as a battery in a clean, cool, ventilated, dry place, and to avoid the sun, radiant heaters or other heat sources influence. The battery should be placed upright, not tilted angle. Between each battery terminal connections firmly. 2) The environment temperature greater impact on the battery, the ambient temperature is too high, the battery will overcharge produce gas, the ambient temperature is too low, the battery will charge less, this will affect battery life. Therefore generally require ambient temperature around 25 ℃, Hills UPS float voltage is set Click temperature. 3) The charge and discharge current of the battery charge and discharge current is generally represented by C, the actual value of C is related to battery capacity. For example in terms of, if it is 100AH ??battery: C = 100A. Panasonic lead-acid maintenance-free battery charging current best about 0.1C, the charging current must not be greater than 0.3C. Charge current is too large or too small will affect battery life. General requirements for the discharge current at 0.05 ~ 3C, UPS in normal use can meet this requirement, but also to prevent the occurrence of unforeseen circumstances, such as a battery short circuit. 4) UPS batteries are charging voltage due to alternate ways of working, under normal circumstances, the mains is charging only when power will be discharged. To extend battery life, Hills UPS charger general by way of constant current limiting control after the battery is fully converted to float state, each section of the float voltage to about 13.7V. If the charging voltage is too high will cause the battery overcharge, otherwise the battery will charge less. Charging voltage is abnormal, it may be a configuration error caused by battery or charger failure caused due, so when installing the battery, be sure to pay attention to the battery size and number of the correctness of different specifications, different batches of batteries do not mix. Do not use inferior charger plus charger and cooling issues to consider when installing. Depth on the battery life of 5) discharge depth of discharge is also very large, the deeper the battery discharge, the fewer the number of its recycling, and therefore should be used to avoid deep discharge. While Hills UPS has a low battery protection, generally single battery discharge to about 10.5V, UPS will automatically shut down, but the situation light load or no-load discharge discharge if UPS is in, can also cause deep battery discharge . 6) regular maintenance of the battery after a certain time should be checked regularly, as observed its appearance is abnormal, measure the voltage of each battery is average and so on; if not long-term power outage, the battery will always cause the battery state of charge of such activity deteriorates Therefore, even without power, UPS also require periodic battery discharge test in order to remain active. Discharge test is generally three months time, the practice is UPS load - preferably at least 50%, and then disconnect the mains, so that UPS is in battery discharge status, discharge duration depends on the battery capacity is generally speaking a few minutes to tens of minutes to restore electricity supply, continue to charge the battery after discharge. Above is an analysis of MGE battery use and maintenance methods made, factors affecting battery life are the following: Installation, temperature, charge and discharge current, charge voltage, depth of discharge and charging and other long-term.