Lightweight foam concrete wall panels equipment

Lightweight, light wallboard quality solid economy, 75mm to 120mm thick wall board plaster masonry walls on both sides of the weight + 1/3 ~ 1/5. Solid wall beams to optimize structure, easy to install in a non-load-bearing beams outside, so that the whole interior layout more reasonable. Thin body - increased use of the area by the National Building partition board norms, with a solid wall 75mm and 100mm respectively, instead of the traditional brick 120mm and 180mm thick brick wall. Use a solid wall system, construction of the wall to increase 10 ~ 12m to extend the use of 1m2 area, usage increased by 4% to 6%, is well suited for retail and residential walls and household. Fireproof noncombustible solid wall partition system performance up to the national A-level standards, after siding installation is complete, with excellent stability and integrity, good fire resistance, fire and smoke can poison gas confined within the area affected by the fire, and do not emit toxic gases, for your safety more of a guarantee. Insulation, solid wall insulation is building an outdoor, ideal for energy saving in the wall plate. It has on climate change with the seasons and automatically adjust the indoor air moisture content function, set the humidity level to maintain a balance, to the effect of ecological regulation, in line with the development trend of modern residential architecture. 100mm thick insulation capacity of the heart wall of noise 46dB, much higher than other brick wall of sound insulation, sound insulation in line with the requirements of the National Housing. Moisture-proof, water-proof solid wall panels for medium density fiber reinforced cement slab, has a good waterproof, moisture resistant, can be used for kitchen, bathroom, basement and other wet areas, wall plates will not appear due to moisture absorption of pine, back to halogen deformation, strength decreases and so on. Experiments show that, in the absence of wallboard can make any finishes, filled with water after the cell body with cement bonding, the back wall can be kept dry without leaving any traces, the walls will not appear condensation in humid weather drops. Simple construction, short construction period is assembled solid wall construction, the wall height of 4m or less, each about three workers, an average of one day to ship 15m2 more skilled workers, and no longer smooth sided wall plastering and masonry building wall construction efficiency compared to more than 10 times. Environmental GRC light wallboard product features a capacity of light: per square meter wall 46 ± 2kg, brick and concrete walls weight ratio decreased about 80%, reducing the project cost basis; 2, thin wall: 90mm thick and 24cm Performance brick rather, can expand the use of housing area of ??10% -13%; 3, excellent quality: compressive strength, impact resistance, flexural failure load, surface density, hanging power, sound insulation, fire resistance, drying shrinkage, etc. are in line with national building materials industry, "JG / T169-2005 building walls with the Light Board" standard; 4, board level: reducing mortar layer, directly after the putty stucco; 5, fast installation: nails, saws, drilling, planing cutting easy, flexible construction, pipe and take the easy line, saving time and labor to install and improve construction speed 3-5 times; 6, low prices: prices are lower than traditional solid walls, reducing the total cost of the project; 7, no cracking: original slot tenon structure and construction technology, a good solution to the problems of the industry for many years the wall cracking problems. First, the new wall formwork equipment market prospects of new formwork panels as new wall materials, widely used in building walls, exterior walls, roof, walls, can speed up the construction speed, reduce labor intensity, reduce project cost, improve Building use area. Use of industrial waste production of wall materials, but also save energy, protect arable land, is the development direction of the wall of reform, in line with national brick and industrial development policies. According to Office of the State Council issued the order, the relevant state ministries jointly issued a document, respectively, in 2001-2009 three times, the capital of China's 577 cities and included "no stick" cities, require batches prohibit or restrict production, use of solid clay, and gradually extended to small towns and rural areas. To achieve by 2010, new wall materials wall materials production accounts for the proportion of the total of more than 55%, and the proportion of building applications, more than 65% of the population standard. Require the development of a whole wall is made of clay to the non-clay, solid to hollow, small to large, heavy development in the direction of light, the light panels precisely for its lightweight, environmentally friendly, energy saving, utilizing waste , efficient, high quality, low cost and become the first choice of the construction works. Currently wall molding methods are mainly two types: one for fixed vertical molding machinery; the other for mobile extrusion method, also known as ground-molding. The former belongs to molding process, which is part of the extrusion process. Second, the vertical molding equipment basic information a partition board, the company's stand-mode light partition board equipment with hydraulic control and electrical control system, hydraulic opening and closing of the mold, high automatic temperature control, mechanization and automation; 2, electricity water, steam can be heated, stripping fast curing period is short; 3, molding cavity structural rigidity, high precision system board thickness accurate. Good flatness; 4, a plastic core tube lined with a metal pipe, durable, no-rinse, saving time and labor when electric pumping pipe; five consecutive net design sheets, cloth mesh uniform, accurate and convenient; 6, a multi-purpose machine, wall plate length, thickness adjustable, suitable for the production of GRC, magnesite, gypsum, ceramic and other light sheet; 7, equipment, technology is mature, reliable, good durability; 8, after years of practice, the formation of a mature, complete production, service, installation, construction, inspection system. 1. formwork abrasive car: Features: fixed line, watering fast with vibration. Advantages: High yield, low investment ratio, income, suitable for an annual output of more than five hundred thousand square plate production scale. Uses: mainly used in the production of composite sandwich plate or solid slat wall formwork is widely use: As a result of vibration casting molding plastic concrete, wallboard compactness, impermeability, retaining muscle is good, and can be used steel wire mesh, steel mesh, steel grid and other ways to accompany the tendons, solid wide scope, interior and exterior can be applied. Wall Equipment [1] produced the product surface smooth, dense and high, truly industrialized production of new pipeline construction wall panels. Greatly reduces the labor intensity of production workers. Completely changed the previous legislation die, die-casting day many drawbacks. Such as: mold using a low turnover rate; electric heating or steam heating needs; a single product category; soundproof. Wallboard equipment products used in a wide source of raw materials, no regional limitations. The main use of sawdust, straw, rice husk and a variety of crop straw, adding inorganic materials (such as talc, construction waste, diatomaceous earth, fly ash, etc.) processed by special technology. Low production costs, less investment and quick. The machine uses dual drive on the roll extrusion process, from product sizing, Ingredients, spreading, compound, complex pressure-time completion of the production process of genuine, high degree of automation equipment, smooth operation, specifications arbitrary adjustments. Product surface smooth, dense and high, truly industrialized production of new pipeline building wall panels. Greatly reduces the labor intensity of production workers. Completely changed the past formwork, flat die-casting many drawbacks. Equipment characteristics: 1, hydraulic synchronous opening and closing mold, mold hydraulic opening and closing end, saving labor intensity, simple operation high efficiency. 2, the machine forming modules: 8, can produce 90-120 type 2 adjustable. 3, length: 3.2 meters, can be adjusted freely. 4. Weight: 5 tons. 5, the electric heating power: 11.5 kilowatts. Automatic temperature control. 6, the molding cavity rigidity, high precision molding, accurate thickness, good flatness. 7, continuous sheets of cloth mesh net, accurate and efficient distribution network, the tension is high. 8, a group established production mode of production, no vibration, blanking molding. 9, wide application, there is no hole hole components, non-distribution network components can be produced. Production process: a good process stability, eliminating the process of workers operating in randomness, a unique mixing process and molding process, can reduce water-cement ratio of lightweight aggregate concrete, wallboard strength improve performance, reduce systolic wall value. 2, advanced technology, the first injection material, after wearing tube; can reduce the water-cement ratio, improve strength; without the addition of another additive; lower costs, reduce vibration and avoid segregation and inhomogeneous high yield. 3, automatic temperature control, their own steam heating or electric heating, special curing device (optional) self-curing, curing stripping cycle is short, improve productivity, conservation need to build another cellar, cost Please note: Due to raw materials, parts, labor such as price changes and technology updates and other factors, this investment plan is for reference only, one, formwork light wallboard plant condition plant, site: 500-1000m2; single power: 15 kilowatts; production workers: 3; Total investment: about 20 million; single annual: 30000 m2. Second, light wall formwork profit analysis (with an annual output of 30,000 square meters 90mm lightweight partition board, for example) 1, covering 500 square meters, 60 square meters simple workshop production workers 3, 380V electricity, water . 2, the unit cost of 28 yuan / square meter (fiberglass mesh 1.8 yuan / square, cement, perlite, fly ash aggregate 22.8 yuan / square meter, the management fee revenue 0.5 yuan / square meter, labor costs 1.5 yuan, utilities 0.8 yuan, 0.5 yuan chemical additives). 3, the overall costs 42 yuan / square meter (unit cost 28 yuan + installation costs 12 yuan / square + shipping costs 2 yuan / square meter) 4, the market reference price: 75 yuan / square meter. 5, the annual output: 30,000 m2 × 75 yuan / square meter = 2.25 million yuan. 6, the annual profit: 30,000 m2 × profit per square meter (75 yuan -42 yuan) = 99 million. The above data the actual production of the Company, construction draw. Wang intends to invest light wallboard project customers visit the company's actual inspection! Formwork lightweight wallboard product features a capacity of light: per square meter wall 46 ± 2kg, brick and concrete walls weight ratio decreased about 80%, reducing the project cost basis; 2, thin wall: 90mm thick performance and 600px brick rather, can expand the use of housing area of ??10% -13%; 3, excellent quality: compressive strength, impact resistance, flexural failure load, surface density, hanging power, sound insulation, fire resistance, drying shrinkage, etc. are in line with national building materials industry, "JG / T169-2005 building walls with the Light Board" standard; 4, board level: reducing mortar layer, directly after the putty stucco; 5, fast installation: nails, saws, drilling, planing cutting easy, flexible construction, pipe and take the easy line, saving time and labor to install and improve construction speed 3-5 times; 6, low prices: prices are lower than traditional solid walls, reducing the total cost of the project; 7, no cracking: original slot tenon structure and construction technology, a good solution to the problems of the industry for many years the wall cracking problems. Basic information a formwork equipment, the company's stand-mode light partition board equipment with hydraulic control and electrical control system, hydraulic opening and closing of the mold, high automatic temperature control, mechanization, automation; 2, electricity, water, gas are heated, stripping fast curing period is short; 3, molding cavity structural rigidity, high precision system board thickness accurate. Good flatness; 4, a plastic core tube lined with a metal pipe, durable, no-rinse, saving time and labor when electric pumping pipe; five consecutive net design sheets, cloth mesh uniform, accurate and convenient; 6, a multi-purpose machine, wall plate length, adjustable thickness, suitable for the production of GRC, magnesite, gypsum, ceramic and other light sheet | cement foam insulation board set 7, equipment, technology is mature, reliable, good durability; 8, after years of practice the formation of a mature and complete production, service, installation, construction, inspection system.