STDC-2 bearing induction heater

Jingjiang bearing heater factory direct bearing installation tool by the end of the promotion, custom large bearing heater, bearing heater lowest end ZHANG 139 526,298,740,523,849 550,582,880,390,815 Jingjiang Connaught Instrument Co., Ltd. specializes in producing micro STDC Bearing heater models: STDC-1 / STDC-2 / STDC-3 / STDC-5 / STDC-7. Good quality and low price, STDC-3 for heating the outer diameter of the bearing 340mm or less. STDC bearing induction heater selection table: Model STDC-1 STDC-2 STDC-3 STDC-4 STDC-5 STDC-7 power 1KW 2.0KW 3.6KW 8KW 12KW 24KW rotating arm YES YES YES YES YES YES inner diameter 15-100 30-160 30-16050-250 70-40075-400 outer diameter 150 340,340,480,700,920 60,115,140,200,265 width 350 controls the way microcomputer microcomputer microcomputer microcomputer microcomputer microcomputer traditional heating methods such as cooking oil, electric heating, flame heating often following problems: laborious work intensity; destruction of the bearing itself and the lubrication state of the material structure, easy to damage the bearing; annealing temperature is too high resulting in bearing; bearing deformation damage caused uneven heating; a risk of oil leakage . The new induction heater: Works induction heater for use alternating current produces an alternating magnetic field, alternating magnetic vortex so that the metal workpieces quickly fever. In the induction heating process, the temperature increase is only the workpiece is heated metal parts, induction heater itself and the non-metallic portion of the workpiece is heated and not heat, so you can use an induction heater for heating tape and pre-sealed bearings lubricated bearings. Connaught research and production of induction heaters compared with similar products, technical advantages: fast heating, heat evenly; inverter technology, any heating of small parts to be realized, and to solve the blind hole aluminum heating problems; without any External cooling system can run continuously; easy to use, digital temperature control; optional rotating and sliding heating rod; time control accuracy up to 0.01 seconds; temperature control accuracy ± 2 ℃; automatic calibration power, automatic degaussing; by magnetic probe and microprocessors that monitor the heating process. Heating bearing temperature: When bearings with induction heater, we recommend heating temperature is 110 ℃, when the bearing temperature is above 125 ℃ will change the structure of the bearing material, accelerated aging and even damage the bearings bearing, non-bearing class closed metal the workpiece can be heated to about 300 ℃. STDC series bearing heater Instructions: 1. Make sure the power supply voltage is accurate; 2, the heater power plug into a power outlet, turn on the switch on the side of the heater housing, after power, digital screen with bright display temperature 110 ℃, At this heater for temperature control mode; 3, Press ▲ ▼ to select the heating temperature of the workpiece. Press ▲ ▼ to a temperature change is 1. Press and hold the ▲ ▼ fixed temperature changes continuously. 4, when heated to a set temperature, there is an audible alert and automatically shut down; 5, if necessary to maintain the temperature function, item 4 Before operating temperature is maintained simply by pressing button. 6, if the time control mode, simply press the boot time to enter the time control mode. Time settings can be arbitrarily selected within 99 minutes and 59 seconds. Press ▲ ▼ to change a value of a first time, press and hold the ▲ ▼ fixed time value changes continuously. After the selected time, press the START button to start the heater for heating the workpiece. 7, when heated to set the time, there is an audible alert signal, and automatically stop; when using the time control mode, and then without a temperature sensor, the temperature sensor at this time should be removed from the workpiece, to extend the life of the sensor. Jingjiang Connaught Instrument Co., Ltd. has been engaged in the production of heaters 10 years, through continuous accumulation of technology innovation and experience in the development and production of a series of instruments promise for all types of workpieces induction heaters, such as ZN series of controlled induction heater, ZND series of environmental heater, ZNE series microcomputer control induction heater, ZNY series induction heater, ZMH series mute induction heaters, SM series carts induction heater, ZNH versatile heating plate / plate heater, BGJ Series Induction puller Other OEM production of a series: HA series bearing heater, YZHA series controlled induction heater, GJW series induction heater, YZHTR / FAG HEATER series heater, YZRA / YZDC series heater, YZSC sensor puller, YZCK fast gear heaters. The company can be customized according to customer requirements of various types of heaters, artifacts include: various types of bearings, gears, impellers, bearing inner ring, ring, ring, couplings, and other special-shaped workpieces. Just provide your requirements, our company can design a program to make you satisfied with the heater, to provide you with a convenient way to piece disassembly area. Our production of heaters products meet and leader in the domestic and international similar products. Widely used in mechanical maintenance department and mechanical appliances manufacturing units in metallurgy, mining, textile, paper, petrochemical, chemical, power, mining and other fields.