Epoxy Jiaxing [quote how much money one square meter price quote _ Epoxy how much money one square meter

Jiangsu Po Mega Epoxy construction process economy [Suzhou Po Mega Project] ------- floor before the design basis ground investigation works design and construction program of economic reality epoxy thin coating Epoxy construction program for rugged, crack repair area, basic ground intensity difference to the availability reinforced epoxy primer, again looking very poor self-leveling screed or cement screed, foundation treatment is a thin coating of epoxy floor project The key quality assurance, improper handling will affect the quality of the project. Construction conditions: 1, epoxy floor construction, the temperature should be higher than 5 ℃, the optimum temperature is 10 ℃, air humidity should be less than 85%, dry white concrete surface, the ground should be less than 5% moisture, rain and fog Weather must postpone the construction. 2, should be in a sealed condition, windows and doors installed in place, can not have the phenomenon of cross-construction, the ground can not have local moisture, or oil phenomenon; 3, concrete grade is greater than C25, the floor surface to be tight overall light level, do not have from the sand or hollowing phenomenon, can not have structural cracks; 4, on the ground floor epoxy floor construction, the original proposal laying concrete floor waterproof layer. Concrete foundation ground handling: remove laitance ground surface, increasing the density of the concrete surface, so that the ground with Epoxy primer increases adhesion. 1, Suzhou Po Mega imported concrete floor grinding machine pretreated to remove surface laitance and provide a certain roughness and flatness, and enhance the adhesion between epoxy coating and concrete. 2, the original crack the ground using V word-way cutting process, and then use epoxy grout will crack filled, while using the original floor epoxy mortar handle more serious damage to the place and to ensure synchronization vacuum clean floor surface. 3, the joints get rid of the old debris and clean after treatment with a solvent-free epoxy material repaired and marked. Note: The new concrete floor must be smooth, firm, can not afford to sand, the height difference between 2 mm / 2M less maintenance than 30 days, the moisture content of 5% or less. Thin coating of epoxy primer floor construction is mainly a closed surface of dust, so the primer penetrate the ground level to strengthen concrete surfaces do fastness. 1, before construction of the first primer march ground moisture content determination: the water meter, and 5% to the primer coating, also with a suitably large absorbent paper laying on the ground, surrounded by tape stick well to make absorbent paper seal, one to two days, check absorbent ignite the situation, if you can paint primer flammable, combustible intermittent moisture content is high, the need to use a primer or do off the water wet. Flame the moisture content is too high, the ground should be maintained, not construction or determined in accordance with conditions on the ground. 2, using the two-component penetration epoxy primer roll again after sufficient mixing, closed the grassroots level. For severe local damage the floor (from gray) and then penetrating epoxy primer batch painted again until the primer is dry, if the pit where the use of coating materials to repair after adding quartz sand mixed Local sanding dust. Note: The primer paint roller or by scraping, when to do thin uniform coating can be used in time, after coating and shiny, dull place (rough cement of the ground) were painted up in due course. Thin coating of epoxy floor coating construction according to the construction of the ground situation in the coating, in order to ensure smooth topcoat surface, while enhancing the hardness of the floor. 1, a thin coating of epoxy floor coating paint mixed with quartz sand after mixing mortar Scraping the first pass, pending scratch layer dry, polished overall need vacuuming. 2, some areas with poor floor epoxy floor paint mixed with quartz sand mixed mortar Scraping the second time, pending scratch layer dry, polished overall need vacuuming. Note: When the construction to remove the tooth tip big bubble, pick to coarse impurities, if approved fill uneven or too smooth, you need to fully sanded to clean and vacuum. Epoxy construction: Xiaoshan Po Mega uses a two-component epoxy floor paint coating thoroughly mixed, with short hair roller (to prevent hair removal) coating. Note: When the construction immediately remove impurities found sand, paint mixing bucket if the state was hardened, and must be replaced at any time to stop using the mixing bucket. Epoxy floor coating is mainly decorative effect, it's a very thin film, poor wear resistance and scratch resistance, if the factory floor have gone forklifts, machinery and equipment, laying Epoxy construction area selection process, can not meet the needs, the ground is very easy to be damaged, suggested the use of epoxy floor construction process. Phone: 18012733925 QQ: 515920218 E-mail: 515920218@QQ.com Website: http: //www.bmjdp.com Address: Wujiang District, Suzhou City, Jiangsu Province, with the town Matilda district No. 963