Laser anti-counterfeit labels, Dongguan City-art printing, security labels Humen
Laser anti-counterfeit labels, Dongguan City-art printing, security labels Humen
Plate technology (1) exposure film first plate by the size of the crop is good best 2-3mm vacuum plate is larger than the film if the film will need to be cleaned of dust and dirt eradicate the use of ethanol and clean. Protective film film with the film's version of the film with material thrown off the plane and on the face plate connection. Open air vacuum between the film and the plate clean line. Set up the required exposure time. sticker printing, label printing security label printing, bag printing, this time to the platesetter lamp light intensity and font size of the plate is determined. If there is a plate the size of the font should leave together determine the exposure time of the short exposure time characters small print and fine lines long exposure time. Exposure small print should be some characters can not be closed vacuum drying to prevent the plate with a mask to hide empty when hide. (2) scour the sun good plate with double-sided adhesive tape on the active board bidirectional scour erosion washout initiative to the plate until the bottom of the tank scour erosion before it is necessary to write Shimizu stickers printing, label printing, bag printing, setting the temperature erosion. (3) drying the washed well plate with a sponge to absorb plates floating on the surface in the drying chamber for drying temperature is usually set at between 60-70 ℃ can be. Time for 10-20 minutes. (4) after exposure sticker printing, label printing, bag printing, boring after plate, should once again exposing the photosensitive inadequate, some not completely cured completely cured in this process so that the plate arrived proper hardness specifications. Above platen plate technology for resin version of the plate resin version of its way domestic use hard bottom base plate. Of course imported polyester plate version can also use this form. Here are some round flattened polyester version that is fully automatic sticker print edition plate technology. Laser anti-counterfeit stickers for use one. Label appearance pattern observed: a laser anti-counterfeit labels pattern observed to be hand-held laser tag watch at a point source. Such as sunlight, incandescent light, you will see a bright, clear patterns (such as cloudy or under fluorescent light will be showing no clear pattern) security labels, if not see the next start point light pattern, you need to turn or move laser tag until the angle to see so far. 2. The security label paper pattern observed to be hand printed labels placed under the light, you can clearly see the color pattern. Two use security sticker: 1. uncover laser holographic security labels use patterns: one kick laser holographic security labels pattern when lifted, the application of a fingernail along the edge of the label lift parts, finger pinching parts being lifted, and then forced tear opened, the hologram should be attached to the residual portion remaining in the surface, the flatness of the label is destroyed, can not be reused. 2. The use of scratch-type identification: scratch-type security code labels when ink coverage scratch, scratch the first tentative, then decide the size of the force, not the beginning of excessive force, damage following digital ink coverage, such as individual identity When the cover is difficult to scratch off ink, can add a little water infiltration at the security label production, half an hour Zaigua. 3. uncover label use: When you opened the phone security identification code lift, you should first make sure the surface pattern of prompt language, then prompts lifted from the correct position. Gently lift the edge with a fingernail identification section, fingers clenched being lifted part hollow security labels, and then slowly opened, bottom left on be affixed, digital back of the ground floor should be complete and easy to identify. Laser anti-counterfeit labels, Dongguan City-art printing, security labels provided by Humen, Dongguan City-art printing Limited. Dongguan Wing Arts Printing Co. (www.ylys1288.com) is Dongguan, a leader in adhesive products, over the years, the company is implementing the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customer needs. Dongguan City-art printing leadership with the staff warmly welcome all inquiries negotiations to create Dongguan City-art printing a better future.
Contact Detail
Company Name: | Dongguan Wing Arts Wangniudun paper products firm |
---|---|
Employee Number: | |
Annual export: | |
Year Established: | |
Contact Person: | Mr. Zhao() |
Telephone Number: | 0769-81760898 |
Company Address: | Wangniudun under Cao Dongguan City Industrial Zone, Dongguan City, Guangdong, China |
Zip/Postal Code: | 523000 |
Find More Related Products
- Laser anti-counterfeit labe..
- Supply Tianjin construction..
- OPGW cable fittings | Xinji..
- Site scaffolding steel fenc..
- Guangyuan election Which vi..
- Simple wood pellet machine,..
- Sophie Bouvet price benzofu..
- Wuwei mall decoration compa..
- ● A Hebei and Shandong Yan..
- Guangyuan which hospital tr..
- Leshan vitiligo Which is go..
- Dongguan Gutian County Logi..
- Transparent double-sided ad..
- Siemens inverters Agents
- OSRAM 44892SP 12V35W instru..
- Herbal tea deacidification ..
- eps lines Price, Weifang Bo..
- Indoor eps lines | Weifang ..
- Liangshan City Which vitili..
- Zhengzhou to Yueqing logist..
- Shenzhen Fu Yong What male ..