Manufacturers of high quality durable proof lights Explosion GBL5211 road lights

 Manufacturers of high quality durable proof lights GBL5211 proof road lamp house fully qualified professional Lighting up the highest price for your best service and quality trusted manufacturers partner company for many years production and trade sales and one continuously updated from year to year quality only to meet customer demand for more long-term sent to various regions of the continent. Products can be used in chemical plants, power plants, coal mines, gas stations, coal preparation plant, loading docks, substations, control rooms, square, boiler room, cold storage, waste, sewer, metallurgical plants, underpasses, tunnels, factories shed, underground, cruise ships, warehouses, factories, marine, watchtower, railways, shipping, oil tanks, fire trucks, tower cranes, boats, gas stations, billboards, conservation room, road, bridge, air box, railway tunnels, initiations, open-air reservoir area , coking plant, parking, underground parking, accident, cinemas, stairs, underground, tents, pharmaceutical companies, stage, fences, grilles, hotels, facades, badminton courts, outdoor basketball courts, trench, workshops, pharmaceutical plant, dyeing, oil, punch, garages, high shelf, table tennis stadiums, baths, rooms, hospitals, outdoor, roof, canopy, roadway, playground, cafeteria I. Scope of the company to meet the petroleum, petrochemical, metallurgy, railway, power plants requires ships and other inflammable and explosive places lighting, research and development and production of BLC8610 proof road lights, widely used in explosive areas as well as a variety of indoor work site as fixed lighting. II. Features 1, proof certified by the national authority, in full accordance with national standards for explosion proof, proof the highest level, can work safety in explosive areas. 2, the use of high-intensity gas discharge lamp as the light source, high luminous efficiency, high color, light and soft, uniform illumination, with an average life of up to 20,000 hours. 3, using high-tech surface coating treatment, rain resistant, permanent not rust; Transparency latest photocatalyst nano materials, automatic decomposition stains, sticky oil, ensure illumination lamps. 4, the shell is made of special high hardness alloy materials, multiple damping structure, with a strong shock and impact resistance, can be used in harsh outdoor environments and long-term. Three technical parameters Rated voltage AC220V 50Hz proof mark Exd IICT4 / T6 power factor greater than 0.9 degree of protection IP65 Insulation class I category WF2 from higher than 2.4 Inlet thread and cable sizes G3 / 4 ", φ10 ~ φ14mm Lamp Dimensions: 624x371x175mm ballast: φ330x310mm weight lamp: 11.35Kg ballast: 6.2kg equipped with light: Order No. equipped with a light source rated power flux average life BLC8610-J250 MH 250 21000 20000 BLC8610-J400 MH 400 36000 20000 BLC8610-N250 HPS 250 27500 28500 BLC8610-N400 HPS 400 50000 28500 IV. Use the lamp is equipped with cable penetration inside the pole, then the lamp body by clamping ring on the pole 60mm, adjusting the lighting direction, tighten the clamping ring bolt fixture fixed ballast tank explosion loaded pole bottom of the base, open the ballast cover and unscrew the inlet compression nut, the lighting cable wear into the ballast tank in accordance with the wiring diagram for wiring. Loosen the ballast tank to another inlet compression nut, the input power line penetration ballast tank in accordance with the wiring diagram for wiring. When replacing the lamp, with a suitable screwdriver or Other tools into the side of the mountain portion of the hole lid unscrewed the lid, and then unscrew the broken bulb, a new spin on the bulb holder, and then the above method will cover. five tighten. Notes 1, replace the lamp When wiping the glass, you must power off and lighting fixtures to be cooled for 2, when used, has some light surface temperature is a normal phenomenon;. Transparency center temperature is higher, not touch three lamps in use After the cut, when turning the lamp does not start immediately, this is a normal phenomenon; you can start again until after the normal lighting the lamp to cool for 15 to 20 minutes; should avoid hot start so as not to damage the bulb warning: 1, non-electrified openings. ; 2, you must turn off the power before replacing bulbs and remove lamps six quality assurance company has passed ISO9001: 2008 international quality system audit certification, the products strictly enforce the ISO9001 international quality management system standard production, to ensure the quality of products fully meet the state standards and design. requirements, the product of 7-year warranty (one year lamp warranty), since seven years from the date of purchase, the product under normal use of any failure by the company responsible for maintenance free.